headphone desk hook 3d models
106196 3d models found related to headphone desk hook.thingiverse
This is a hook for Headphones to hang off of the underside of your desk. they are designed for turtle beach headphones but should work with most headphones with a small amount of padding. The thickness of the desktop I modeled this for was 24.45mm...
thingiverse
Fits on my IKEA desk of 51 mm thickness. ...Very strong at 15-30% infill to hold up heavy headphones.
thingiverse
This is designed to fit ATH-M20x Audio-Technica headphones, but it should really fit any. It fits snug on the edge of my desk that is about 15.6mm thick with an 18.4mm overhang. There's 3 tiny little teeth to grab the bottom of the desk. ...If your desk...
thingiverse
I made this hook to fit on an IKEA Galant desk with a desktop of 20mm thick and it fits nicely. There is some room left for doublesided tape if you want it to stick into place. ... The part sliding over the desktop is only 3mm so it will not get in the...
thingiverse
... http://www.thingiverse.com/thing:44705 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44705 Instructions Using the following options: thickness = 5 width = 20 jack = 10 hook_height = 20 depth = 40 desk_height = 33
thingiverse
Clips onto the edge of 20mm thick desks. ...Holds up pretty well even at 10% infill. Instructions Remixed STL with Blender to adjust the desk clamp height so that it fits 20mm thick desks.
thingiverse
Fits any desk around 32mm thick, or in my case, a door as a desk. ...It was a bit too small, but it still works great.
thingiverse
Remix from http://www.thingiverse.com/thing:400503 , fit any desk around 2.5cm thick. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/iWY7EpoXEvB
thingiverse
This desk clip is designed for my Bose QC35 II headphones, though I'm certain it'd work for many other models of headphones. ...It's a very quick and easy print, and something I designed for my daily use.
thingiverse
... the surface of the desk from time to time. The headphones I use are the Corsair VOID RGB headphones, but the hook is wide enough (35mm) to accommodate the vast majority of headphone bands and it also works great for holding my Oculus Rift HMD.
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/4rgoeoSanmQ
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/4rgoeoSanmQ
thingiverse
A really basic headphone hook for gluing to the bottom side of a desk. ...Holds my Sony MDR's nicely while they charge.
thingiverse
I've seen cool designs on thingiverse for headphone hooks, but almost all of them mount to your desk with a clip that is desk width specific, might slip off, and again, result in a slightly reduction to desk space. This design mounts only to the...
thingiverse
I liked user anoochit's version better, but it was made for 2.5cm desks. This is for ~3.5cm desks! ...Works great with AudioTechnica m50.
thingiverse
This particular hook was made for the desk cover 22.5mm. ...It is not that perfect but still printable and usable.
thingiverse
My desk has a square tube frame underneath a wood board top, so this hook snaps on to it. The far end of the bottom clasp is 33mm from the front edge of the desk surface, and the total height of bar and desktop is 35mm. There's a small support strut...
thingiverse
... my desk width exactly. I have a 25.65mm thick desktop. Update. I lengthened the upper and lower arms as it was rocking forward on the desk. ... Instructions Must be printed with raft/supports.
myminifactory
A simple headphone mount intended to be screwed to the bottom of a desk. ...Holes fit #7 screws.
thingiverse
A simple headphone mount intended to be screwed to the bottom of a desk. ...Holes fit #7 screws.
thingiverse
... Jarvis Bamboo desk. ...The original appears to be for a 20mm desk, this remix is for a (/my) 23mm desk. It also holds Jabra's controller. Because my 23mm is a tight fit, I have also included a 24mm version. ...I recommend using the 24mm version.
thingiverse
A clamp with a hook designed for my Bose QC35 II headphones. My desktop is exacly 30 mm thick and the print fits perfecly. ... I added fillets of 2 mm on the inner edges and that fits the edges of my desktop perfectly.
cults3d
Durable gaming headphone hook designed for 27mm thick desk / table edge. Model can be easily adjusted or scaled to fit custom desk / table thicknesses. Compatible with all 3d printing technology. FDM recommended. ...(.stl and .3mf file formats included)
thingiverse
A small and simple headphone hook designed for my Sennheiser HD650 headphones. ...It uses two small screws (thread outer diameter <4 mm, screwhead <6.3 mm) to attach to the underside of a desk.
thingiverse
This is an under-desk headphone hook. It attaches with 2x #6x5/8" screws (or similar). I wanted this to keep my headphones accessible, and get them off my desk. It is just a quick SOLIDWORKs design that is designed for easy mounting. I have...
thingiverse
This is an under-desk headphone hook. I've created a small hole at the top for a 3mm screw to go through to drill this hook to the underside of a desk. However, if you would like, you may also put tape to stick this to your desk. Tips are always...
thingiverse
A screw-on solution to an under desk headphone hook. This is designed to utilize a single screw from an Ikea ADILS leg that is commonly used with the LINNMON table. The hook is designed for headbands less than or equal to 35mm wide. V3 Edit -...