headphone holder clip 3d models
420027 3d models found related to headphone holder clip.thingiverse
... QC35s). This remix creates an arc-shaped resting surface so that the headphones are resting on the entire headband. The model has been created with a 2.5cm table thickness in mind. ...This can easily be adjusted to match tables of any thickness.
thingiverse
A headphone holder for the Phanteks Eclipse P300 PC case.
cults3d
This is currently designed to tightly hold to a shelf/desk with a wood thickness of about .5in" ...changeable in 3D Builder and Solidworks file is also included.
thingiverse
This is currently designed to tightly hold to a shelf/desk with a wood thickness of about .5in" ...changeable in 3D Builder and Solidworks file is also included.
thingiverse
at the moment i hang my headphones off a corner, they sometimes fall off so i designed this the headphone dip is 40mm across the desk gap is 17.2mm the width is 40mm
thingiverse
Headphone holder I made for a 20mm thick desk. It has a headphone logo on top and a golden spiral logo on bottom (for fun). ...Best printed on its side.
thingiverse
... to fit pretty much most desks. ... Use the actual holder bit from anth92's Headphone Holder. ** Thingiverse renders a weird preview of the .scad file, but it seems to work all right in Customizer. ...Let me know if it's really bork and I'll fix it.
cults3d
This design arose from the need for a bracket to hang my headphones on the wooden ceiling above my setup. Since it is a bit high I needed a somewhat long bracket to be able to attach it to the wooden beam and reach it comfortably from below. The...
thingiverse
The Radiate lamp from Nordlux, a 3W LED lamp, which you can find herehttps://www.nbm24.de/baumarkt/de/shop/Lampen-Leuchten/Lampen-Kategorien/Stehlampen/?card=131172 or in...
prusaprinters
The Radiate lamp from Nordlux, a 3W LED lamp, which you can find here https://www.nbm24.de/baumarkt/de/shop/Lampen-Leuchten/Lampen-Kategorien/Stehlampen/?card=131172 or in black...
thingiverse
Print horizontally Added editable file The resulting quality and functionality It depends purely on your settings thanks to the following
thingiverse
Customized version of https://www.thingiverse.com/thing:3072883 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3072883
thingiverse
Customized version of https://www.thingiverse.com/thing:3072883 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3072883
prusaprinters
My version of one these, along with a cable holder.Print in whatever material you wish! ...The tolerance of the M16 bolt should be enough for most printers. </p><p>Only tried printing with 0.4mm nozzle and 0.2mm layer height.</p><p>Enjoy!</p>
thingiverse
This is a headphone clip designed for hanging your headphones on a MacBook Pro when it is sitting vertical in a doc. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/0qpceVNtzoo
thingiverse
Designed this 3.5mm headphone jack clip to get mounted on my helmet. It's designed for a jack with about 9mm diameter. ...Used double sided tape.
thingiverse
Added a spot to hang headphones to the Blynclight Clip. I had also added a spot for a 5mm machine screw to keep it from wobbling on the partition but it holds just fine. ... Printed in ABS on QIDITECH I.
prusaprinters
These Headphone Holders are designed to clip into existing features of specific monitor types to hold headphones on the side of the monitor. If the clip force is not sufficient due to tolerances of the monitor and/or dimensional variations of the...
thingiverse
I needed to glue a headphone holder to my shelf and made one that fits one "tesa powerstrips" glue pad. Those are ubiquitous in Germany and it works pretty well. I know it is very bad to roll the cable like in the photo, but I do it like that...
thingiverse
Clip-on holder for headphones for DELL monitor, e.g. ...P2717H UPDATE: 2020-03-30: Added LEFT side version Check out my other designs: https://www.thingiverse.com/DaVinci2000/designs
thingiverse
Customized version of https://www.thingiverse.com/thing:3072883 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3072883
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
prusaprinters
Clip-on holder for headphones for DELL monitor, e.g. P2717H</p> <p>UPDATE:</p> <p>2020-03-30: Added LEFT side version</p> <p>Check out my other designs: <a href="/DaVinci2000/designs">https://www.thingiverse.com/DaVinci2000/designs</a></p> <h3>Print...
pinshape
Based on the Original Belt Clip Headphone/ Hearing Protection Holder. This version has a hand on the clip. Use the clip for hanging your beats headset on, instead of crushing your skull. I typically use this for hearing protection, out on the flight...
thingiverse
So I designed a simple holder that will hold the Vision, take up the slack and clip it onto my belt. The latter is useful as it keeps access to the player and reduces the stuff I end up putting in my pockets! The opening for the player is a little on...
pinshape
I created this to hold my over the ear hearing protection while I was out on the flight line at the airport. ...They work great and work with head phones as well (Dre Beats).
thingiverse
My desk is built using Square Tubing for the desk frame. I wanted something that would click into place around the square tubing and wouldn't let go. This was my third iteration of this design and I think this is the winning result for me. ... The...
thingiverse
... the original clip from falling off. You attach it, not by placing it in one go over it, but from the side, clip it under one side, then the other and then slider it further over the original clip and now the headphones will not easily fall off.