headrest cup holder 3d models

Made this to to allow everyone to use the back of headrest cup holder from the original design. Simply use 2 short strings or cords to hold the cup holder to your head rest. I originally made this because my kids didn't have a good place to put...

I'm also planning on making phone holder attachments for the front so you can set a phone up like those headrests that have tvs on the back of them. When I finish that, I'll add it here. Overall, the cup holder part works great. It holds snuggly a...

Made this to hold a drink on the back of the front seats in my car. Allows the rear passenger to have a very convenient location. Consider supporting my work through Patreon! ...https://www.patreon.com/user?u=16231908

Has two pen holders as well. I will upload a single version also. The holes are 6" apart and will work with many vehicles with the same offset. Some slop so +-.125" should work. Mine is a Ford F150. Large file because I hate seeing rough...

The Toyota van has door cup holder, but it's inconveniently located and angled. If you're storing closed bottles, it works fine but with cups with lids, its just makes a mess. 3D printer to the rescue! This holder slips onto the the headrest...

You should print the clamp in 60-70% infill.

You should print the clamp in 60-70% infill.

A headrest holder for the rear headrests on a Honda Ridgeline. Probably fit other models. The front hole is 15mm and the back is 14mm. ... I designed this to give me better visibility out the back window..

Holds headrest while they are being measured

This is a spool holder that lets you keep the door on your FlashForge Adventurer 3 without making any modifications to the machine for printing external filament. All of the other designs are hours and hours, tons of wasted plastic and you have to...

smartphone holder for headrest. hole size (diameter) - 100mm hole center pitch 130mm 7??? ?? ???? ????. ...^^

... Remove the headrest from the seat. Put the holder on the top of the seat and reinsert headrest through the holes in the tabs. Connect power cable to the V1. ... **Note: this hasn't been crash tested and is intended for off-road use only.**

The second version of holder for the iPhone (6, 6s, 7, etc), fastened at the spokes of the headrest (center distance 140 mm) prev version https://www.thingiverse.com/thing:3103598 In addition you will need: DVR mount (type - see on pics) with nut 1 x...

Hat holder designed to fit the headrests of a Landrover Discovery 3/4 (LR4) or most cars with 12mm headrest rods by DAR01 UPDATE: New model added with strengthening rib to improve load carrying ability. Clips securely onto the headrest rod allowing...

The clamp can be changed (redesigned) to suit other tablet covers, the rest of the holder should fit Volvo car's headrest in this model seat, like in the photos. ...I used M5 and M6 nuts and bolts.I used Button head bolts as not to damage the leather...

It probably fits most Fords with similar headrests. Instructions: Print the part insert the V1 in the part Remove the headrest from the seat. Put the holder on the top of the seat and reinsert headrest through the holes in the tabs. Connect power...

Designed to 1) fit most headrest post diameters, 2) have the cut out angle on the anchoring plate positioned relative to the head rest post (not the plate itself) so it accommodates for the tilt when the holder is used with some weight, 3) be a...

I made this to hold my snowbroom in my car. ...I think the distance between the headrest posts should be the same for most car models.

A simple iPad headrest mount. ...Just put it around the bars of the headrest in front of you and put in the bolts. After that, put on the nuts. ...You will need an m3 bolt that fits the hole and a nut.

Designed to clip onto Car headrest post so you can hang bags from it. I reccomend using PETG or ABS in order to withstand heat without warping in the summer time. ...2 part print.

... somewhere for quick access. ...Only solution was to design holders. It's one of the most useful prints I've ever done since its in use every day. It fits 14mm head rest rods and distance of 150mm between them. ... I used them in Volkswagen Touran.

Only solution was to design holders. ...It's one of the most useful prints I've ever done since its in use every day.</p> <p>It fits 14mm head rest rods and distance of 150mm between them.</p> <p>I used them in Volkswagen Touran.</p> <h3>Print...

Headrest

One simple bag holder that can fit any Headrest pins.

i have a tablet holder with a suction cup and i wanted to be able to swap it to a headrest holder i tried my best but im really bad at designing stuff^^ Print Settings Printer Brand: RepRap Printer: i3 Rafts: No Supports: No Infill: 30% or more...

... table. ...Aslo you will need 2 hex screws for each holder to mount (I used 6x20, but you can test with shorter one M6). Nd it would be nice to protect cabin plastic with some soft material where metal guids of headrest ends line on one of the photos.

... It can be adjusted to fit the specific mobile phone, so that it has a secure fit. The holder can be attached in such a way that all buttons and plugs are still accessible. ... You need some small screws and a m6 screw an a m6 threaded insert

Instructions You will need to print out the iPad holder portion from hein0170's backseat cinema and assemble it as he indicates. You will need two rods to span the distance between the headrests poles. Since they were easily available at our...

There is space for charging cable and headphone jack.   NOTE: Many variants are available, please measure your phone and car headrest center and shaft Ø as per picture and I will update design immediately to suite your need.  Post your dimension in...

... to other headrests should be relatively straightforward. I was inspired by RyGuy's headrest mount system giving this design a simpler (although less sturdy) mounting mechanism than hein0170's. ... Be sure to read the instructions before printing.