heltec esp32 lora 3d models

The USB connector is sunk in because on the ESP32 board I'm using, a "WEMOS LOLIN32 ESP32 Lite", the Lipo connector (for some silly reason) faces the same way as the USB C socket. The specific display I've used is a "Best 4.2inch E-paper Display...

Case for ESP32 Cam Pan and Tilt Camera  with Servo control.As you can see the rounded shape of the part case_cam_xl_+_support_tiltl.stl is not printed very pretty, so it might be helpful to add support.Detailed Description and...

Here is the github of the project: https://github.com/sle118/squeezelite-esp32 I designed it for the ttgo t7 v1.4 esp32 module, 5 buttons (10 mm height), a rotary encoder (module), a .96'' i2c oled, and an i2s amplifier. The buttons and the display...

This project was inspired by "ESP32 cam case" by Kosec (https://www.thingiverse.com/thing:3873612) and "ESP32 CAM Case with Gopro mount" by ToXIcG (https://www.thingiverse.com/thing:3876150). ... Kosec suggests printing the top part at 0.15mm...

The small 38pin header on the bottom of the case is more of a guide than really a base to clip your esp32 onto. A small touch of hot glue may be needed to keep the esp32 firmly in place. No specific printing instructions. The design is...

... modules. I'm not thinking about plastic surgery. ESP32-CAM 日本では、技適に対応する為モジュールの換装が必要である。 AC110V-DC 5V 700mAポリスイッチ付きモジュールとESP32-CAMと外部アンテナの構成です。 USB変換コンセントが不要な為、節電と各部材の過熱等を考慮できる状態です。 熱を考慮して耐熱フィルムで包んでいます。 蓋は、爪の加工を考えましたが、他のモジュールを組み込む予定の為 何も整形は考えていない。

A simple housing with a swivel mount for the esp32 cam. The lid is just snaped on, no screws needed. ... The hole in the side of the housing is meant to be used for an extern antenna.

Housing for ESP32-CAM with jimbal joint for wall mountic. The housing is provided also with slot for sealing cord dia. ...2.5mm and slot for RJ 12 female conector.

Remix case for the 34 pin version of the DoIt ESP32 DEVKIT V1 board. Fit is pretty tight on the pins but it will work. ... This is a remix from https://www.thingiverse.com/thing:4125952

Mounting frame for the Version 4 of the ESP32 firebeetle to mount upside down, so e.g. ...LEDs and reset-button is accessible from the outside.Screwholes are 1.6mm for M2.Print with 0.2mm and raft works fine.

This is a near-exact 3D duplicate of the Lolin D32 Pro Devboard, employing the ESP32 Wrover module as its core component. ... This replica can be utilized for rendering purposes or to create mock-ups of the device.

ESP32-CAM Motor Shield Miniplan - Robot fun (Facebook Page) https://www.facebook.com/miniPlanrobot/ 電商販售連結 ICSHOP https://www.icshop.com.tw/product-page.php?28709 Self-tapping screw M2 x 8mm x 5 PCS Self-tapping screw M2 x 6mm x 8 PCS Motor : N20 (...

Here is a model of box to make your surveillance camera based on an ESP32 CAM. The box has 3 axes of rotation. It is easy to print and assemble. ... V2: added ventilation holes and external antenna slot.

My first homemade 3D printed thing. ...Made with Shapr3D on iPad Pro Nothing to say except that I made it cause I didn't find any case for that particular model of ESP32. ... https://fr.aliexpress.com/item/4000366505771.html

Simple robot with motors and esp32, lipo.If you like this design, a subscribe to my youtube channel would be highly appreciated: http://www.youtube.com/@codrutrat3108 . ...I will start to post robotics/automation/drone content in the near future.

I haven´t found a 3D model of an Arduino nano ESP32 online so i took it upon myself too upload. ...I have simply downloaded PCB project file from Arduino and uploaded it to Altium to create a 3D model.

I designed this project specifically for an ESP32 POE device that serves as a reliable temperature monitor. ...The comprehensive details of the project can be found at https://github.com/hixair/Data-center-temperature-monitor.

This was created to hold a WEMOS ESP32 and an RS485 to TTL. ...There is a hole for a netowrk cable, and an opening for a Micro USB for power.

This project concerns a mask for attaching an ESP32-CAM card to a gas meter of type Schlumberger g6 (see photo). ... I have designed it Using OpenSCAD and used configuration parameters that allow to easily adapt height, width and thickness.

Two-piece enclosure and encoder knob (two choices) for ESP32 WLED universal dev board by Shields and more.

Deckel für das Nutzen der ESP32-CAM Platine ohne USB Port. ...Stattdessen mit Wlan und der passenden Zusatzantenne.Passend für Gehäuse von user eMJay1805: https://www.thingiverse.com/thing:5794920Gehäuse aufkleben, oder mit Kabelbinder festklemmen.

This is a ESP32-CAM Box for mount in an Edge of the [Creality Eclosure](https://www.creality.com/goods-detail/creality-3d-printer-enclosure) or any other Tends with 8mm pipes

Encasement for ESP32 Feather Board and Power Cell. Designed to shield metallic components from electrical discharges. ...Features a slot for USB Micro connection and an aperture providing access to the power cell's connector and terminal.

Housing for ESP32-CAM with jimbal joint for wall mountic. The housing is provided also with slot for sealing cord dia. ...2.5mm and slot for RJ 12 female conector.

This is a tiny case to hold a mini ESP32 (Wemos D1) and an HLK LD2410C mmWave sensor. ... Fusion 360 project included.AA Battery in picture for scale (I didn't have a coin handy

Basic Setup for a Weather Station. ... Components to Consider: - The ESP32 Firebeetle Microcontroller. - A BME 280 Sensor Module That Tracks Temperature, Humidity and Atmospheric Pressure. ...- A Standard 1050mah Lithium-Ion Battery.

ESP32 nodemcu32 dev Kit v1 enclosure for PCB design. mounted on my weather station PCB design. ... printed on SLA Elegoo mars using eResin Hard Tought black, UV pcb paint yellow https://a.aliexpress.com/_mKNfUSW

From the [TTGO ESP32 T-Camera Case with Wall Mount (Customizable)](https://www.thingiverse.com/thing:3440888), you need to print two files: * espcam_wallmount.stl * espcam_backmount.stl Then, print the case from the [TTGO T-Journal ESP32 with OV2640...

... shield headers, and an ESP32 CAM module. You can find these parts on Amazon by following the links below: mini spring clamps: https://amzn.to/2WoaGxh Arduino Stackable shield headers: https://amzn.to/3ba5O35 esp32 cam: https://amzn.to/2WnxlcZ

Featuring a compact 100mm x 100mm board, the ESP32 Kit is specifically tailored for use alongside Digital Processing Systems in both practical demonstrations and educational programming contexts, making it an ideal tool to enhance learning...