hesine m 505 3d models
127127 3d models found related to hesine m 505.thingiverse
Spool Holder for the Hesine M 505, Anet A8 Spool Mounting Setup Print Settings Printer Brand: RepRap Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 mm Infill: 20 %
thingiverse
Case for Melzi Board Designed for Hesine M-505-B (Prusa i3) to protect the board, Size: 210 x 50 x 40 mm Print: 170g / 2h 45min Print Settings Printer Brand: RepRap Printer: Prusa i3 (Hesine M-505-B) Rafts: No Supports: No Resolution: 0.3 mm Infill:...
thingiverse
improved spool holder for hesine M-505 (clone of i3). just print out this holder twice and fit any spool with ID 35-65 to it. The original M8 shaft is used, but instead of nuts i used some 8mm shaft collars for quick changing the spools. With this...
thingiverse
For Hesine M-505 (i3 clone) a Filment guide with included dust remover. just insert a piece of sponge inside the barrel and guide the filament through. can be mounted directly on a 8mm frame or even a M3 nut can be inserted in the pocket and the...
thingiverse
Slic3r Infill / Hesine M-505 Config Slic3r 1.2.9 Config High Quality 0.1 mm - GCODE: 212 KB (1,98g / 13 Min 25 Sec) Fine 0.2 mm - GCODE: 153 KB (1,83g / 7 Min 55 Sec) Wizard 0.3 mm - GCODE: 138 KB (2,02g / 6 Min 28 Sec) Quick 0.4 mm - GCODE: 142 KB...
thingiverse
X-Axis Tensioner compatable with Hesine M-505 (Prusa i3) printer. ...Clamp model can be found in original tensioner by rejaak. Print Settings Printer: Hesine M-505 (Prusa i3) Rafts: No Supports: No Resolution: 0.2 Infill: 25
thingiverse
For the Hesine M 505 Spool holder. ...Print Settings Printer Brand: RepRap Printer: Anet A8 ...
thingiverse
... ctrlV and remixed "Prusa i3 Spool holder for 6mm frame" by loco. ...I made holder more stronger and replace frame mount holes with 8mm screw mount holes. Print Settings Printer: Hesine M-505 (Prusa i3) Rafts: No Supports: No Resolution: 0.3 Infill: 25
thingiverse
Z-sensor holder for Hesin M-505 Print Settings Printer: Hesin M-505 Rafts: No Supports: Yes Resolution: 0.2 Infill: 15% Notes: Cura slicer
thingiverse
;Sliced at: Thu 14-01-2016 17:03:09 ;Basic settings: Layer height: 0.06 Walls: 0.4 Fill: 30 Print Settings Printer: mendel m-505 (prusa I3) Rafts: No Supports: No Resolution: 0.06 Infill: 30
thingiverse
... how to construct large objects (e.g. ...this case for the board). My idea is to connect this two smaller items to one large object (23 cm size). Print Settings Printer Brand: RepRap Printer: Hesine-M505B Prusa i3 Rafts: Doesn't Matter Supports: No
thingiverse
Extruder Fixation Plate for PTFE Tubes or Bowden Extruder, etc. ...Print Settings Printer Brand: RepRap Printer: ...
thingiverse
I made this holder for a 4 mm PTFE Tube. It mounts directly over the extrudermotor, as you can see on the picture. The tube is held in place by a M3 screw, but the hole should by small enough to hold the tube in place by itself. If using a screw be...
thingiverse
My printer used to "wobble" around during printing so i decided to add some fixation plates in the corner which helped well. ...Print Settings Printer Brand: RepRap ...
thingiverse
replacement part for Anet A8 (prusa i3) or Hesine m-505 X axis belt mount Print Settings Printer Brand: RepRap Printer: Anet A8 Rafts: No Supports: No Resolution: Layer height - 0.1mm, nozzle - 0.4mm, speed 60mm/s. Use brim. ... ...
thingiverse
I've mounted my extruder head up-close so the pipe almost touches the feed mechanism. There is only one screw length of pipe sticking out so I needed an even shortened M505 cooling nozzle. ... I think this is the shorter you can get because a shorter...
thingiverse
One more spool adaptor. ... Print Settings Printer Brand: RepRap Printer: Prusa i3 ...
thingiverse
Filter for PTFE Tubes and Wall mounting. ...To use with an interior piece of sponge Print Settings Printer Brand: RepRap Printer: ...
thingiverse
Fits Ball Bearings with 19mm diameter, the Filament Spool fits very nice and tight. The center Part can be printed with or without Support. ...If you print it without Support you might need to clean the inside with a knife, but the bearing should still...
thingiverse
Just test printed this and works fine for me. Its a bit short, because the original was bumping and scraping on the print and movin it. ...Shoutout to the original creator : Arjjck.
cults3d
I was used "Universal Spool Holder 18-56mm II" by ctrlV and remixed "Prusa i3 Spool holder for 6mm frame" by loco. ...I made holder more stronger and replace frame mount holes with 8mm screw mount holes.
thingiverse
Even shorted M505 cooling nozzle remix. My extruder nozzle is screwed close to the tension gear and pulley. ... I needed to remove 2mm so this cooling nozzle would not touch the bed.
thingiverse
It is for bowden. If you have other size of spool hole (height and orgglass width) or want to change angle use customizer or edit openscad file directly. ...Customizer is buggy and shows angle wrong (full 360 degrees)
thingiverse
Centered Fan Nozzle *Update 10.12.2016: Thanks for all your downloads and prints, I am very surprised that so many people liked my design :) On several requests i added a V2 version with a lesser angle on the back for better printing. Have fun...
thingiverse
There is no fixing for Z-axis shaft in Hesine Prusa i3 M-505 This small thing will fix this issue :) Print Settings Printer: Hesine Prusa i3 M-505 Rafts: No Supports: No Resolution: 0.2 Infill: 100%
thingiverse
Upgrade of the popular fan blowing with resizing and adding vertical height adjustment https://www.thingiverse.com/thing:1620630 I centering it by the geometric center of the hothead because air flow is stronger at the base of the ring. New...
thingiverse
... при попытке головки доехать до x-концевика. Установка данной детальки решила эту проблему. Сдвигает концевик на 2см вправо. Print Settings Printer: Hesine Prusa i3 M-505 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 100%
thingiverse
The rod has some shifting. ...I make remix for fix it. У M-505 вертикальные шпильки маленько сдвинуты. Пришлось сделать ремикс :) Держится без болтика достаточно туго. ...Родные болты крепления мотора почти подходят :)
thingiverse
Extruder fun duct, designed for Hesine m-505 3d printer, (PLA) Print Settings Printer: Prusa Like Rafts: Doesn't Matter Supports: Yes Resolution: 0.3 Infill: 40% Post-Printing
thingiverse
Extruder fun duct Mark-2, designed for Hesine m-505, anet-A8 and sunhokey prusa I3 like 3d printer, (PLA) Print Settings Printer: Hesini M-505 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: .2 Infill: 40% Post-Printing