hevort vs voron 3d models
9805 3d models found related to hevort vs voron.
thingiverse
A MASSIVE round of applause to MirageC; not only for his design but willingness to share it with our 3DP community. Please check out his work and join the fun. This is a remix of the recently released split carriage design for the STD (6mm) XY...
thingiverse
Almost the same number and length of shafts are required as with the opposite Motor Mount and Pulley mount (except for the two Dowel Pin 5x40mm for the belt binder). The same goes for the idler and pulley. ...
thingiverse
This is an attempt to correct some of Mr. Oliver's bullshit, like this: • The inscriptions are too convex, it prints poorly. • The color emblem is not very important to me, let it be part of the detail. • A fillet on the bottom edge of the part...
thingiverse
These are belt covers for a printer with a bed size of 415mm x 415mm. I was well underway with my enclosure befor MirageC came out with the Acid Bee Theme enclosure. I just sized, cut and mounted polycarb sheets to my frame. I then left...
thingiverse
For those that want to run a HEVO Z-axis with the Hevort printer. ... These are re-worked mounts for the 12mm rods to be held better on the bottom and adjust the position of the rod on the top because the rails of the Hevort.
thingiverse
I moded the Rapido X-Car designed by Hevort to use the Bondtech LGX Light. MGN9 ADXL345 Mount CPAP Fan-Duct Rapido Hotend Bondtech LGX-Light the weight of this setup is about 275g(not UHF) i only tested without UHF but should also fit...
thingiverse
Took the original design from MirageC's HevORT ZR V2 - MGN Rail assisted self leveling Z Axis with Ball screw and Z Wobble Management. Adjusted the CAD model to accommodate 3030 Aluminum Extrusion instead of the original 2020 Aluminum Extrusion.
thingiverse
**This Thingiverse page contains files up to V1.1** - To see if this is the latest revision visit: [GitHub HextrudORT Releases](https://github.com/MirageC79/HextrudORT/releases/tag/V1.1) ##** Join the Support Discussion Forum now to get latest news...
thingiverse
**This Thingiverse page contains files up to V1.1** - To see if this is the latest revision visit: [GitHub HextrudORT Releases](https://github.com/MirageC79/HextrudORT/releases/tag/V1.1) ##** Join the Support Discussion Forum now to get latest news...
thingiverse
Hi all, Here is the frame aligner with optional leg caster attachment for HevORT and upcoming HevORT HD printer. 16 pieces of 25mm M6 screws and lock nuts to secure casters in place required. Optional: 50 pieces of M6, 8mm or 10mm grub screws...
thingiverse
Here is a carriage for the Hevort HT and STD 6mm belt configuration. It is using the E3D Chimera hot end dual extrusion setup (In Bowden Config) The main carriage assembly can be used a good base for other extruders (it has a 5 bolt pattern on the...
thingiverse
... familiar with all of the parts. You'll find the BOM here: https://miragec79.github.io/HevORT/bom/BOM_ZR_V2.htm OTHER I suggest you check out the fusion360 link where you can browse the orginal hevort Z and see how it works; https://a360.co/3gweJiw
thingiverse
It's a remix of the hevort Speye Mainpart: https://www.thingiverse.com/thing:4441076 Please print the original Plunger (v1.5) Why I have done a remix: You don't need the 2 bearings at the side you can insert 2x teflontube 4mm / don't need the M6...