hex bit adapter 3d models

Human Interface eXtension Bit Adapter

... It's thin enough that magnetic screwdriver will hold the bit and the adapter in. This is a superior arrangement in most cases. PLA is strong enough for this design and has worked quite well for me. No supports, rafts, or brims are needed.

Outer Dia: 15mm Height: 20mm Hex Hole: 7.51x6.5mm Handler Socket Size: 6.5x6.5mm Use maximum wall and 100% infill for durability. ...It takes 28min and 3g filament for me.

Bit adapter with magnet, 1/4" female hex on magnet side, 1/4" quick release dog end hex on opposite side. ...2-3/8" overall length.

Bit adapter with magnet, 1/4" female hex on magnet side, 1/4" quick release dog end hex on opposite side. ...2-3/8" overall length.

A minimal single solid piece adapter that locks a 2.5mm allen wrench in place using tension with a hex bit on top so it can be used with a power drill or screw driver. Print with 100% infill to prevent breakage under high torque. ... Use pliers to...

However, this other set was equipped with 6.35mm or 1/4" hex shaft bits, which are incompatible with the Wowstick's mini bit requirements, featuring a 4mm shaft. To solve this problem, I created an adapter that can accommodate any standard 1/4" bit...

It's a handy adapter that lets you turn 1/4" hex bits in tight spots. You can either hand-turn it or fit it snugly into a 12mm socket or wrench. This design prints with precision on my trusty Tevo Tarantula, although the bit does come out slightly...

... and then putting them back on again. ...So, I came up with an adapter that lets me use a power screwdriver and a standard hex bit to turn the knobs in no time. ...Maybe all Thule knobs are interchangeable, but someone out there might find this handy.

I needed a screwdriver with interchangable hex bits for narrow spaces, made this handle. A simple hex extension adapter can be press fit into this handle. I had to use vise since it was tight, you could print it at 105% scale and probably fit...

One end is a standard hex bit, the other a pentagonal bit the size of the EZ-IO needle. This inexpensive electric screwdriver from harbor freight will likely do the trick (if you don't already have one) as its inexpensive and appears similar to...

A hex bit socket and a posidrive screwdriver head are tools that can be used for various tasks, such as tightening or loosening bolts and screws with hexagonal heads. ...These tools offer versatility and ease of use due to their interchangeable bits and...

Little adapter that helps cleaning the filter with a drill instead of turning it by hand. ...The drill-side is a 6,35 mm hexdrive that fits most little screwdrivers like an Ixo.

... it with a paper clip melted into the plastic (i haven't tried this yet). ...Print with the hex side on the printer bed (think the model is the other way up) with max resolution/infill and support on. ...tasks about 30 min to print on my ender 3.

Print with the hex side on the printer bed (think the model is the other way up) with max resolution/infill and support on. tasks about 30 min to print on my ender 3. ...Print Settings Printer Brand: Creality Printer: Ender 3 Supports: Yes Filament: ...

... nominal side length of 5 mm. ... May 11, 2017: The hex dimensions were incorrect and have been fixed in the updated SLDPRT & STL files. May 13, 2017: I reduced the size of the bit adapter on the hex shaft by scaling it down by 3% to get a better fit.

The hex bit holder is deep enough that most standard hex bits will fit snugly to drive the guitar tuner.

Bit adapter that has a standard 1/4" (6.31 mm) shaft that goes to a pentagonal (nominal 5 mm side length). 11 May 2017: I messed up the hex dimensions. They've been fixed with updated SLDPRT & STL files. 13 May 2017: It was too big on the hex shaft,...

Allows 6.35mm hex bits to be used in a tool that only accepts insulated 7.35mm hex bitsFor a comparison between these two hex bit sizes, see the last picture. ...Red = 7.35mm bit, Grey = 6.35mm bit

... To overcome this limitation, I created a custom adapter using Fusion 360, allowing users to employ standard 1/4 inch-sized bits with the 4mm precision screwdriver. ...Simply print the adapter and insert a magnet inside to secure the bits in place.

This version is probably a tiny bit too tight, which I resolved by putting the print on a >90c heated bed, before hammering it on to the grinder. So far it's worked pretty well; turning the hand powered grinder into an electric one. The previous...

This version is probably a tiny bit too tight, which I resolved by putting the print on a >90c heated bed, before hammering it on to the grinder. So far it's worked pretty well; turning the hand powered grinder into an electric one. The previous...

This converts any 1/4" hex bit to function with a 17mm socket in confined spaces. For my particular application, I had to remove rear deck speakers from a 2005 Ford Mustang. The rear-most bolts are approximately 2 inches away from the back window and...

This will adapt any 1/4" hex bit to work with a 15mm wrench for use in tight areas. In my case, I needed to remove rear deck speakers from a 2005 Ford Mustang. The rear-most screws are only about 2" from the rear window and a ratchet or...

... Quadcopters. ...When taking apart complex components, I often wish I could utilize the individual parts from this tool with my trusty Bosch PSR Select Drill. Unfortunately, they don't match up properly, so I created an adapter to make them compatible.

So here's a generic shape with a hole for a quarter inch hex driver bit so you don't have to make one. Drop it into your project, attach it to whatever you'd like, and drive away. My print fit snugly, I had to tap it on gently. It feels secure and...

I connect a hex bit to a square adapter. ...I utilize it along with my Bosch IXO.

I created a tool that can be used with any standard ¼” hex shank and fits into any screwdriver featuring either a keyed, keyless, or ¼” (6.35mm) hex drive chuck. The device works effectively with Black & Decker Phillips style toy screws but may...