higher bed 3d models
162557 3d models found related to higher bed.thingiverse
Remixed from https://www.thingiverse.com/thing:2014167 to mount directly on the Prusa i3 MK3 bed spacers which are 6mm diameter and about 5.45mm high. Included a side by side of thing 2014167 made for MK2 and this one which I remixed to fit the MK3...
thingiverse
Moved the Ball Joint 12mm up to get a better view on the printbed.
cults3d
Original tended to snap at the base, so ive made it a bit stronger
thingiverse
Original tended to snap at the base, so ive made it a bit stronger
thingiverse
This remix is mirrored for a left side mount, has the ball even higher at 26mm total and features a slot for the Pi camera flex cable.
thingiverse
End Caps for Open V-Slot 2020 with Open Hardware logo. This is a remix from https://www.thingiverse.com/thing:398515 I had used the old model for a while but realized that the gopro fit was too tight and not perfect. I adjusted the size, now...
myminifactory
This is a remix from https://www.thingiverse.com/thing:398515 I had used the old model for a while but realized that the gopro fit was too tight and not perfect.I adjusted the size, now it fits perfectly and I uppered the camera angle a little to...
cults3d
End Caps for Open V-Slot 2020 with Open Hardware logo. This is a remix from https://www.thingiverse.com/thing:398515 I had used the old model for a while but realized that the gopro fit was too tight and not perfect. I adjusted the size, now it...
thingiverse
Hi. ... just a new higher bed Handle. i made this new bed handle because the others ones i have found were to low and have some issues with the screws on the Y axis. ... Enjoy.
thingiverse
Remixed to sit higher after I replaced my hotend and the nozzle sat higher than the fan duct
thingiverse
Extra height and width feet to minimize wobbling on higher MPCNC 2.5mm configurations.
thingiverse
A remix of https://www.thingiverse.com/thing:4829074 for putting the headset higher
thingiverse
I also included the already merged stl file including the higher balcony as one single peace so that you do not have to glue it on top after wards if you want to print this whole thing from scratch :) note that the total size has also been increase...
sketchfab
The same mode just with higher resolution maps. ...Still working on it to make it look better.
thingiverse
high i make the esun ebox holder higher with hole for it's cable thanks for W11N4R7 that create this cool product :)
thingiverse
I need this to make the teapot higher (closer to the wall plug) Will also contain tea bags Currently 400g of PLA. Seems a lot. ...Needs investigation WORK IN PROGRESS
thingiverse
I made the box for the undiscovered land tokens some milimeters higher so that you can not only fit the token in, but also the number token. ... I even use 3d printed number tokens found here: https://www.thingiverse.com/thing:2884108 Those + the...
thingiverse
... of the ESP32 housing for the watermeter ki on the edge. ... The new part is a bit higher, to have more place for cables and the ESP32. ... I created a little german tutorial including IObroker config for the watermeter https://youtu.be/zb3AEusPQLQ
thingiverse
This is modeled very similarly to inventaholic's foot but 8mm higher. -Combine this with his power clip: (http://www.thingiverse.com/thing:50775) -So the fan has more clearance for air and now it will also accept this wonderful fan "cap"...
thingiverse
I needed to raise my sofabed to let my robovac under, so I made these replacement foot for the bed to stand 5 mm higher.
thingiverse
Star Trek ds9 bajoran combadge higher resolution less sanding
thingiverse
This a remix for the Hot wheels Rack. ... I've remixed it to be higher, so I can also stack higher cars! ... In the photo you can see 2 higher racks (top and bottom) and one "standard" sized.
thingiverse
--- Remix / AddOn for: https://www.thingiverse.com/thing:3942090 --- The filter was a little too close to the VAT for me, so I wanted it to be 20 mm higher. ... I drew the base quickly and dirty, so I can't guarantee that it will also work with SLA...
thingiverse
Changed the mount mount to be 3mm higher for more camera angle.