himoto rc 3d models
29161 3d models found related to himoto rc.thingiverse
Ingranaggio per Nascada/Himoto RC da 5588 denti. Quello nominato cilindrico11,ha lo scavo posteriore di 1.5 mm. quindi piu' profondo ed aggiornato. N.B. = Un ringraziamento speciale a Federico di Fazio. ...
thingiverse
This is a Himoto/HSP RC Car Body Post. made 80mm long. I've tried to print it vertically but it is best to print it laying flat. Holes are pre-marked not to weaken the overal structure. Fit your body and drill desired holes out. I've printed these...
thingiverse
rc car 1:18 scale lower susp arm dogbone himoto mastadon e18mtl parts If you can not stick the bar into the hole, heat it up.
thingiverse
Had to make pinion gear for Himoto rc car. ... Original grinded by dirt.
thingiverse
I'm using this part to replace the rear or front uprights of my Himoto RC/Car. ...REF: 23604 and 23603
cults3d
I'm using this part to replace the rear or front uprights of my Himoto RC/Car. ...REF: 23604 and 23603
grabcad
Himoto Raptor 5XB RC Buggy Large Scale 1:5HM54012-Rear Reinforcement PlateMaterial Aluminium 4mmHM54012-Horná doska zadná Materiál Aluminium 4mm
grabcad
Himoto Raptor 5XB RC Buggy 1:5 Large ScaleHM54008-Front Upper Top PlateMaterial Aluminium 4mmHorná doska prednáHM54008-Materiál Aluminium 4mm
grabcad
Himoto Raptor 5XB. ...RC Buggy 1:5 Large scaleAluminium Servo Holder Hitec HS-5805MG, Hitec HS-645MGcreated by dzino
thingiverse
Printable chassis on the RC car Himoto Spino. ... 23601 no supports needed 23611 need supports - it is a remix of part from Myles97 https://www.thingiverse.com/thing:2391522 See parts in Onshape here: ...
thingiverse
Experimental frame Himoto Centro 1:18. Not test. All mounting dimensions are taken from the 3D model of the chassis. Update: There was a mistake in the size. Model corrected. ...
cults3d
This bumper is for 1/10 onroad HSP/Himoto/Maverick models. The design has been little bit reinforced. 2,8 mm hole for M3 screws. 3,2mm hole for 3 mm pin. P.S. ...: I will share the other hsp parts in another post soon.
cults3d
This rear hub is for 1/10 onroad HSP/Himoto/Maverick models. 3,2mm hole for 3mm pin. 2,8mm hole for screws. The marked side will be on the front. P.S. ...: I will share the other hsp parts in another post soon.
thingiverse
end cap replacement for himoto E18/basher pitbull suspension.works fine
thingiverse
Hello everyone, this is the front suspension for the Himoto Dirt whip by balkon_lab. ...Balkon_lab is a community founded by Russian children https://vk.com/balkon_lab
cults3d
This lower arm is for 1.10 onroad HSP/Himoto/Maverick models. 3,2mm hole for 3mm pin. 2,8mm hole for screws. P.S. ...: I will share the other parts in another post soon.
cults3d
This shock tower is for 1/10 onroad HSP/Himoto/Maverick models. Second part of the shock tower. P.S. ...: I will share the other hsp parts in another post soon.
cults3d
This rear diff mount is for 1/10 onroad HSP/Himoto/Maverick models. 3,2mm hole for suspension pin. There are two files. One of them has been modified. For easy printing, I removed the protrusion attached to the chassis and replaced it with a...