hkpilot 3d models

SummaryI made this to use a HKPilot Micro on my Quanum Trifecta Build

I made this to use a HKPilot Micro on my Quanum Trifecta Build

This is a case for the HKPilot Mega Mini from HobbyKing. ...I just used a 8 small pieces of thin double sided foam tape in each corner (top and bottom) of the board to hold everything together.

A case to protect you HKpilot/Ardupilot flight controller. uBLOX NEO-6M case: http://www.thingiverse.com/thing:129414 Telemetry Radio Cases: http://www.thingiverse.com/thing:165889 Instructions...

... foam -Glue on the top part. Mount it with an 3mm CFK rod to the Quad Custom Section Other Quad Parts: Micro HKPilot vibration damper and junction box: http://www.thingiverse.com/thing:1212764 Landing Gear: http://www.thingiverse.com/thing:1236091

... APM-Box_Base.stl: Remove the included support with needle nose pliers Custom Section Other Quad Parts: Housing for the Micro HKPilot GPS And Compass: http://www.thingiverse.com/thing:1236051 Landing Gear: http://www.thingiverse.com/thing:1236091

... placement the old one was from HK crappy dimension, now mesured with caliper and tested. ...Very good vibration dampening and light-weight Version With : earBud damper & hkpilot case + double side tape earBud damper & hkpilot screw Version-V2 (m2screw)

HKPilot Micro mount with a bracket to hold a TS5823 200mW A/V transmitter designed for the Quanum Trifecta but will work with others

Micro APM HKPilot slim cover for 30mm PCBoard This version was made in order to be able to mount the controller and minimize weight and size. ...It is a sandwich of about 15mm size.

Designed to mount HobbyKing Micro HKPilot (APM) with double-sided tape/pads on top of it's PDB board in order to reduce vibration transfer from the frame (Peon230). PM mount > double-sided pads > mAPM mount bottom > mAPM mount top (to cover the...

from hobbykings hkpilot micro apm... there wasn't one on this site, so i decided to try my hand at 3d modeling... this is my first time using a 3d program to make something.. came out good for my first time.. 30.13x30.13 to account for...

I purchased the HKPilot Master Set on HK.com Since there is no housing to buy, I designed one. There are two holes for the LEDs on the GPS module. I designed it to put on a piece of transparent 1.75mm filament. It works well. The GPS Module fits very...

For Arduflyer 2.5 from RCTimer. With right angle openings for IO pins. Remix of http://www.thingiverse.com/thing:129411 This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/bwWE9Au9cH3

Fits booms up to 19mm Height: about 120mm Mounting holes for 3mm Screws Use a 4,5mm carbon rod to connect the legs Print Settings Notes: Lander2-Left_w_Supp.stl / Lander2-right_w_Supp.stl includes support, and Lander2-Left.stl / Lander2-right.stl is...

Link to the Ardupilot/HKpilot flight controller case:http://www.thingiverse.com/thing:129411 Instructions Print the two parts. Place GPS module into case bottom with a bit of silicone or epoxy adhesive around the perimeters of the PCB. ...Adhere the...

... for M3 machine screws to self tap. Typically i tap with a steel screws, then secure with a plastic screw. Use CA as a thread locker. https://hobbyking.com/en_us/micro-hkpilot-mega-micro-sized-flight-controller-and-autopilot-with-leads-2-7-2-apm.html

For the Crossfire 2 I ordered from Hobbyking the HKPilot Micro Master Set. This includes a GPS sensor from U-Blox Neo 6M with a shrinking tube. I don't like this, so I created a case for the Neo 6M that fits into the CS2TopAPM plate. The case fits...

For the Crossfire 2 I ordered from Hobbyking the HKPilot Micro Master Set. This includes a GPS sensor from U-Blox Neo 6M with a shrinking tube. I don't like this, so I created a case for the Neo 6M that fits into the CS2TopAPM plate. The case fits so...

part of this set: http://www.hobbyking.com/hobbyking/store/__74654__Micro_HKPilot_Mega_Master_Set_With_OSD_GPS_Telemetry_Radio_PDB_BEC_Power_Sensor_433Mhz_APM_.html) Instructions Case, print with 20% infill and the mast with 100% infill. Use CA to...

Recently purchased the Micro HKPilot Mega Master Set and found the OpenPilot Flight Controller Adapter Plates to be a nice way of mounting the controller. Unfortunately, the NEO-6M GPS that came with the set did not come with any mounting holes, so I...

FAQ: http://www.thingiverse.com/shivinteger/about [>>>] Generating Attributions log: [0] Thing Title : Open Brushless Gimbal [0] Thing URL : http://www.thingiverse.com/thing:110731 [0] Thing Author : turbi [0] Thing Licence : Creative Commons -...

Laser parts: -Frame top -Frame bottom -Arms -Tower sides 3D printed parts: -Landing gear (both in 50mm and 70mm included) -Inner structure separators (both in 15mm and 20mm heigh included) -Tower Top and camera platform (this was printed because of...

(mileage may vary) Controller: HKPIlot (Chinese for APM) Master set http://www.hobbyking.com/hobbyking/store/__58283__HKPilot_Mega_2_7_Master_Set_With_OSD_LEA_6H_GPS_Power_module_Telemetry_Radio_915Mhz_XT_60_.html 10s capable voltage meter:...

My setup is: Apm 2.7 micro gps http://hobbyking.com/hobbyking/store/__64142__HKPilot_Micro_GPS_and_Compass_Module_U_BLOX_7_8g_.html DYS 1804 2300kv motors http://hobbyking.com/hobbyking/store/uh_viewitem.asp?idproduct=66399 AfroESC 30A (you need max...

25X25 mm motor mount for big motors Setup: Motors: MN4010 580KV Props: 15X5 ESC; 40 A Flight controller: HKpilot mega 2.7 with telemtry Battery: 4S 10000Mah, this will give about 25 minutes of flight time Gimbal controller: 2 axis gimbal controlelr...

Post-Printing http://www.hobbyking.com/hobbyking/store/__39036__Turnigy_Multistar_2213_980Kv_14Pole_Multi_Rotor_Outrunner.html ^Motorshttp://www.hobbyking.com/hobbyking/store/__65153__Turnigy_Multistar_20A_V2_ESC_With_BLHeli_and_4A_LBEC_2_6S.html...

FAQ: http://www.thingiverse.com/shivinteger/about [>>>] Generating Attributions log: [0] Thing Title : HKpilot/Ardupilot Flight Controller Case [0] Thing URL : http://www.thingiverse.com/thing:129411 [0] Thing Author : HLMAX [0] Thing Licence :...

Hardware of my copter: 3D printed 250mm Frame Micro HKPilot Mega Flight Controller with Ardupilots APM 3.2 Software. 4x Multistar 2206 2150KV Baby Beast V2 Brushless Motors with 4x 12 Ampere Afro Speed Controllers (with SimonK Firmware) 4x 5030 5...

Hardware of my copter (I know these are some basic items): 3D printed 250mm Frame Micro HKPilot Mega Flight Controller with Ardupilots APM 3.2 Software. 4x Multistar 2206 2150KV Baby Beast V2 Brushless Motors with 4x 12 Ampere Afro Speed...

FAQ: http://www.thingiverse.com/shivinteger/about [>>>] Generating Attributions log: [0] Thing Title : Refillable Pet Fountain Water Filter [0] Thing URL : http://www.thingiverse.com/thing:9001 [0] Thing Author : leghk [0] Thing Licence : Creative...