hobbyking durafly 3d models

Landing skid for fpv racer 260 by hobbyking.

Spinner for Piccole Ali / Hobbyking Macchi C.205 Veltro

A basic GoDiscover floor and shelf (to get the other shelf just mirror the part) The fit is desent but you need to glue the parts in place. To fix a battery use som sort of velcro or similar. Väl mött! ...Print Settings Printer Brand: ...

Customized version of https://www.thingiverse.com/thing:735213 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=735213

Helimax SH101 Servo 1.9g 95mm Lead HMXM2057same asHobbyKing™ HK-5330S Ultra-Micro Digital Servo

abs print inclined

This B-25 Canopy is for the one Hobby King used to sell. ...I print it vertically, nose up, single layer walls, one bottom layer, and zero top layers, then trim excess

Brushless ESC for RC boat, 90 A

I lost the canopy of my Bixler 2. So I designed this. ... 5x5mm neodymium magnets can be glued into the holes on the bottom.

Tired of finding ways to mount your wing cam level or protect it. ...My cam has survived two crashes in this hard case.

Kardangelenk

My purpose for designing this was to protect the MultiWii board on crashes, shield the barometer from prop wash, and to add to the overall weight of the board so that it is less effected by vibrations. I made holes for all of the headers as well as...

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

I made this to help cooling for the ramps controller and arduino! I'm using 2 30mmx30mm fans. You'll need an extra 4 M3x12mm button head screws to screw the fans on... Instructions Print it...

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

BSR SABERTOOTH Mudguards mount with one screw and two zip ties 10% infill Happy printing!

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

Quick model for installation purposes

BSR SABERTOOTH Mudguards infill 10% enjoy!

I have designed this so I can make the cowls in different colors and maybe even layer the colors as my prusa MK3 allows you to swap over filaments mid print.... to do this just turn on layers then cut down to a layer number that you want to change...

clip

I've created this skid to make it easier to mount stuff on the small Bonsai and make it more versible. Fun fact: First flight, flew like a dream, 3cell, 2.4ghz telemetry, naze32, multistar motor, 5inch prop.. Wind took it down.. Not a plane for...

I don't like the cooling setup of the standard Skipper cowl so I designed one that properly feeds cooling air through the motor. The first part of that process was doing a version of the original cowl in Solidworks to check I had the geometry correct...

<p>BSR SABERTOOTH Mudguards</p> <p>mount with one screw and two zip ties</p> <p>10% infill</p> <p>Happy printing!</p>

These pieces are used to prevent stones from ruining the rear wagon. ... They are fixed using a 3x12mm screw, in the already existing hole of the arm.

Customized version of http://www.thingiverse.com/thing:1733767 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1733767

Keeps the pedestal mount of the HobbyKing NEO7 GPS/Compass module from rotating.