holosun 507c dust cover 3d models
149264 3d models found related to holosun 507c dust cover.thingiverse
Pivoting cover for Holosun HS512c red (green, or gold) dot optic.
thingiverse
Cover for the front of a Holosun 407K/507K reflex sight. This is the side that collects the most dust when holstered and is the hardest to clean. ... UPDATE: Added slots on the side to make it easier to grip when removing/installing.
thingiverse
A dust cover for a Holosun HS510C Red Dot optic. Other models I tried were too small, I don't know if they were for previous versions but I couldn't get them to fit. Designed a new version from scratch with rear pull tabs. There is a small...
thingiverse
This is a protective cover for the Holosun 510C Red/Green Dot reflex sight. It's designed to be a "very snug" fit, so there's little chance of it falling off in transport or field situations. It'll protect your Holosun 510C while not in use. ...
prusaprinters
Cover for the front of a Holosun 407K/507K reflex sight. ...This is the side that collects the most dust when holstered and is the hardest to clean. UPDATE: Added slots on the side to make it easier to grip when removing/installing. Print Settings...
thingiverse
Dust cover for the Holosun 407 and 507 v2. Also added easy on/off handles, cutout for the buttons, cutout for the battery tray, and cutout for the solar. ... Recommend reducing contact Z distance as much as possible to improve support quality.
thingiverse
HOLOSUN HS510C TPU cover from dust and scratch. Easy to put on and off, tight fit. It is printed with supports. ...Layer height 0,2 mm.
cults3d
This is a cover for the holosun red dot. There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I...
thingiverse
This is a cover for the holosun red dot. There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I...
thingiverse
Update V3 March '23, added side lips for active retention of cover, probably final edit Update V2 March '23, improved clearance between cover and front of glass This is a basic cover I made for my Holosun 508T. I used the dummy model by Disco_Rex,...
prusaprinters
This is a cover for the holosun red dot. There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I...
thingiverse
I saw there wasn't a cover available online so I made one. ...Print upside down with biggest opening facing up, 100% infill.
thingiverse
This is a simple sight cover for the Holosun510 C. It's ugly but it works. ...It will keep your 510C from getting scratch during transportation or in storage.
thingiverse
Pops off when (airsoft) weapon is drawn. ...Make sure holster is clear when re-holstering.
thingiverse
This is a TPU material cover for a Holosun 510C series Red Dot rifle sight. The design is made to fit the sight snug so that it will not fall off yet is easy to remove. The TPU material will not mar the finish on the sight. It is printed using...
thingiverse
This is a remix of the original cover user jcharouz created this addition only includes the short cover with an added cut out for the battery compartment. ... Link to jcharouz: https://www.thingiverse.com/thing:4380879
thingiverse
Remix to cut out the battery door, relieve the bottom for the M&P slide profile, and added a little nub to increase retention when using TPU.
thingiverse
I needed a cover for my new Holosun SCS-MOS sight on my Glock - and there was none to be found... This is designed for my Glock 21 Gen.5, so the slide might be wider than on your Glock. Print in an flexible material, I used TPU. There are two...
thingiverse
Dust Cover/collector that allows for removable filters I made for my printer enclosure. Works well as is for 90mmx90mm fans. Can be scaled to fit larger fans. Scale x and y. 133.3333% for 120mm fans. ...155.56% for 140mm fans.
prusaprinters
That's why I wanted to share my realization of these protections against dust.The logos are shown above to find out exactly where they are going, even if any geek who does not need this logo to know the exact location of all these covers.I hope they...
sketchfab
Holosun HS403R scope 3d model Archive contains FBX and Unreal Engine 4 texture pack