holosun cover 3d models
136224 3d models found related to holosun cover.thingiverse
HOLOSUN HS510C TPU cover from dust and scratch. Easy to put on and off, tight fit. It is printed with supports. ...Layer height 0,2 mm.
thingiverse
Update V3 March '23, added side lips for active retention of cover, probably final edit Update V2 March '23, improved clearance between cover and front of glass This is a basic cover I made for my Holosun 508T. I used the dummy model by Disco_Rex,...
thingiverse
I saw there wasn't a cover available online so I made one. ...Print upside down with biggest opening facing up, 100% infill.
thingiverse
Remix to cut out the battery door, relieve the bottom for the M&P slide profile, and added a little nub to increase retention when using TPU.
thingiverse
Pivoting cover for Holosun HS512c red (green, or gold) dot optic.
thingiverse
This is a protective cover for the Holosun 510C Red/Green Dot reflex sight. It's designed to be a "very snug" fit, so there's little chance of it falling off in transport or field situations. It'll protect your Holosun 510C while not in use. ...
cults3d
This is a cover for the holosun red dot. There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I...
thingiverse
Cover for the front of a Holosun 407K/507K reflex sight. This is the side that collects the most dust when holstered and is the hardest to clean. ... UPDATE: Added slots on the side to make it easier to grip when removing/installing.
thingiverse
This is a cover for the holosun red dot. There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I...
thingiverse
A dust cover for a Holosun HS510C Red Dot optic. Other models I tried were too small, I don't know if they were for previous versions but I couldn't get them to fit. Designed a new version from scratch with rear pull tabs. There is a small...
prusaprinters
Cover for the front of a Holosun 407K/507K reflex sight. ...This is the side that collects the most dust when holstered and is the hardest to clean.</p> <p>UPDATE: Added slots on the side to make it easier to grip when removing/installing.</p> <h3>...
prusaprinters
This is a cover for the holosun red dot. There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I...
thingiverse
This is a simple sight cover for the Holosun510 C. It's ugly but it works. ...It will keep your 510C from getting scratch during transportation or in storage.
thingiverse
Dust cover for the Holosun 407 and 507 v2. Also added easy on/off handles, cutout for the buttons, cutout for the battery tray, and cutout for the solar. ... Recommend reducing contact Z distance as much as possible to improve support quality.
thingiverse
This is a remix of the original cover user jcharouz created this addition only includes the short cover with an added cut out for the battery compartment. ... Link to jcharouz: https://www.thingiverse.com/thing:4380879
thingiverse
I needed a cover for my new Holosun SCS-MOS sight on my Glock - and there was none to be found... This is designed for my Glock 21 Gen.5, so the slide might be wider than on your Glock. Print in an flexible material, I used TPU. There are two...
thingiverse
This is a TPU material cover for a Holosun 510C series Red Dot rifle sight. The design is made to fit the sight snug so that it will not fall off yet is easy to remove. The TPU material will not mar the finish on the sight. It is printed using...
thingiverse
Pops off when (airsoft) weapon is drawn. ...Make sure holster is clear when re-holstering.
sketchfab
Holosun HS403R scope 3d model Archive contains FBX and Unreal Engine 4 texture pack
thingiverse
Hey guys, I just made an Reddot cover that fits my Holosun HS503G smoothly. Since my AR is an Spartan version i added a random Spartan helmet to it, but also added a clean version. The inner diameter is 29mm so you could adjust your print to your...
thingiverse
This is my attempt at modeling the Holosun 508t v2 RMR. It's not perfect and has no branding on it. Might need to be filed down on the front side to fit your weapon (I had to for mine). ...Have fun!
prusaprinters
This is a mount for the Holosun 509T pattern of micro optics. It's designed to use 30mm M3 hex head capped screws and hex nuts. </p><p>I've tested printing this with up to a 0.6 nozzle and 0.2 layer height- smaller nozzles and layers will work...
prusaprinters
This is my attempt at modeling the Holosun 508t v2 RMR. It's not perfect and has no branding on it. Might need to be filed down on the front side to fit your weapon (I had to for mine). ...Have fun!</p> <h3>Post-Printing</h3> <p...
thingiverse
- Attention: This one is made only for the Holosun HS510C with paintball use only, just to reduce glass damage. If you want to use it on a hot weapon, you need to improve the fittings to withstand the recoil! In that case, you also should check the...
thingiverse
This is a lens protector housing for a Holosun 510C for airsoft. Use the existing torx screws from the sight to mount this. ...There's a relief on the inside for a 2mm polycarbonate lens.
thingiverse
Lens protector for Holosun HS403/503 red dot sight. Accepts a 1" diam. x 1/8" thick polycarbonate or acrylic disc. ... Tip: use electrical tape to shim if tolerance is loose.
thingiverse
... very well with the Bircwood Casey Aluminium Black, but it's fully functionnal! Dovetail locking is for M3x10mm screw and reddot mount is for the original Holosun #6-32 screws. ... Dovetail is 6.2mm / 8.6mm wide (top and bottom) and 2.6mm in heigh.