holosun scs cover 3d models

I needed a cover for my new Holosun SCS-MOS sight on my Glock - and there was none to be found... This is designed for my Glock 21 Gen.5, so the slide might be wider than on your Glock. Print in an flexible material, I used TPU. There are two...

Pivoting cover for Holosun HS512c red (green, or gold) dot optic.

Hardcover for Holosun 507c Reddot

HOLOSUN HS510C TPU cover from dust and scratch. Easy to put on and off, tight fit. It is printed with supports. ...Layer height 0,2 mm.

This is a protective cover for the Holosun 510C Red/Green Dot reflex sight. It's designed to be a "very snug" fit, so there's little chance of it falling off in transport or field situations. It'll protect your Holosun 510C while not in use. ...

Cover for the front of a Holosun 407K/507K reflex sight. This is the side that collects the most dust when holstered and is the hardest to clean. ... UPDATE: Added slots on the side to make it easier to grip when removing/installing.

This is a cover for the holosun red dot. There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I...

This is a cover for the holosun red dot. There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I...

Update V3 March '23, added side lips for active retention of cover, probably final edit Update V2 March '23, improved clearance between cover and front of glass This is a basic cover I made for my Holosun 508T. I used the dummy model by Disco_Rex,...

A dust cover for a Holosun HS510C Red Dot optic. Other models I tried were too small, I don't know if they were for previous versions but I couldn't get them to fit. Designed a new version from scratch with rear pull tabs. There is a small...

Cover for the front of a Holosun 407K/507K reflex sight. ...This is the side that collects the most dust when holstered and is the hardest to clean.</p> <p>UPDATE: Added slots on the side to make it easier to grip when removing/installing.</p> <h3>...

This is a cover for the holosun red dot. There are 2 versions, one for rail mounted and one for slide mounted dots. Print with extra perimeters so the model is solid. No infill needed. NO supports needed, if your printer copes with bridging well. ...I...

I saw there wasn't a cover available online so I made one. ...Print upside down with biggest opening facing up, 100% infill.

This is a simple sight cover for the Holosun510 C. It's ugly but it works. ...It will keep your 510C from getting scratch during transportation or in storage.

scs

Dust cover for the Holosun 407 and 507 v2. Also added easy on/off handles, cutout for the buttons, cutout for the battery tray, and cutout for the solar. ... Recommend reducing contact Z distance as much as possible to improve support quality.

... of http://www.thingiverse.com/thing:1793692 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1793692 Instructions Using the following options: width = 40.6 letter_size = 50 str = SCS letter_height = 5 font = Consolas

Some game-ready model created by me. ...All model based on real holosun micro.

This is a TPU material cover for a Holosun 510C series Red Dot rifle sight. The design is made to fit the sight snug so that it will not fall off yet is easy to remove. The TPU material will not mar the finish on the sight. It is printed using...

This is a remix of the original cover user jcharouz created this addition only includes the short cover with an added cut out for the battery compartment. ... Link to jcharouz: https://www.thingiverse.com/thing:4380879

Remix to cut out the battery door, relieve the bottom for the M&P slide profile, and added a little nub to increase retention when using TPU.

i used PETG 100%infill printed it upside down with supports

Wise SCS Diameter 34.9 or 31.8

a cool looking handgun rocket launcher toy replica or something SCS-AD stands for Smart Clip System - Aereal Destroyer model in .stl and .ADW

Holosun HS403R scope 3d model Archive contains FBX and Unreal Engine 4 texture pack

Linear Bearing SCS 20UU

Pillow Block SCS 10UUDiameter: 10mm

MESHPALETTE - SCS-4 (SANKIN)W1200x1000L-H900 (MADE IN JPAN)【DATA】----------------------------STEP-AP214 &amp; 3D-DWG (Bricscad)SW2017 Modeling export.

it was a desighn for a scooter clamp to fit scs bars but i could not print it

this is an insert for oversized scooter bars with a slit this prevents the slit compressing with scs compression which allows for better compatibility for bars and scooters