homematic hb rf usb 2 rpi rf mod case by 3d models

Flange SW RF 0.75 INCHI 150LB

FLANGE WN RF 20 INCHI 150LB

Motorbike keychain inspired by the iconic font on the side of my trusty Suzuki RF 600R motorcycle.

This is a case for AstroPrint running on Raspberry Pi 2 & 3, designed specifically for the Robo 3D R1 plus printer. The device proudly displays both the R1 plus logo and the AstroPrint logo on its surface. Version 2.0 boasts an additional space for...

Desk Stand for Great scott Gadgets Hack RF One

Round Bottom Chain Conveyor RF 350capacity 100 t/h

Mazda MX-5 RF 2016 Printable Car in separate parts

Enclosure for my Garage Smart RF Arduino Remote

Core Component of Rebooted Proton Pack's RF Amplifier Circuitry

This is a basic wall mount designed to hold RF remote controls for use with RF main power outlets.

Tutourial: https://youtu.be/Vc4EnuKAKTE PENTAX/COSMICAR 8-48mm F1.0 LENS MOD C to RF mount conversion Had this lens laying around for a while because none of the adapter on the market fits this lens due to its large read mounting plate. So I've...

This is a snap-fit case for the HomeMatic WLAN Gateway developed by user amunra in the FHEM forum. ...For details see the forum thread: https://forum.fhem.de/index.php/topic,62651.0.html Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2...

The Fournier RF-4 is a motor glider powered by a 1500 CC 4-cylinder opposed inline engine, enabling self-launching with an extensive range. It is a single-seat aircraft used for personal flights, gliding, and long-range sport planes. Designed in...

Hello, wanted the feets from the Klipsch RF-7 Mk2 on my Mk1 but there are no spare parts available. So i made these out of copper filament (Silk copper) and black filament (Giantarm) The thread also works with a layer height of 0.2 but you can go...

Alternative to Canon ET-101 Lens hood for Canon RF 800mm F11 Lens Hood

RF Power Meter from Ali-Express0.1 - 600 Mhz -75dbm to +16dbm

Square Cheek RF V5 100% inside ear to ear measurement is 205mm (same as EFX helmet)

Autobots Unleash Fury on Decepticon Stronghold with High-Stakes RF_ID Key

Case for the HomeMatic Doorbell Sensor: A Non-IP Version Solution

The Fournier RF-4, a motor glider powered by a 1500 CC engine, offered long-range capabilities, self-launching features, and versatility as both a personal plane and sport aircraft. Designed in 1966, it was equipped with a retractable monowheel, a...

SMA RF connector flnged with 4 holes. Brass with PTFE dielectric. ...Model based on the Tyco electronics part model 1478967.

I lost the Battery cover for my Yongnuo RF 602 RX Lightning Equipment. ...So i designed this spare part.

BBS RF 17 inch rim for scale models in 1/24 scale. ...Can be scaled to fit any other scale.

Nite Owl Lens RF variant Same as before 205mm inside ear to ear measurement (same as EFX helmet) at 100%

... 26. ...You can attach a dot site or other accessories to it. GINDAN RF G 26 https://www.tokyo-marui.co.jp/products/aircocking/gindanrf/323 The GINDAN RF's G 26 model comes with a 20 mm rail that allows you to attach a dot sight and other accessories.

I've soldered two channels of a HM-MOD-Re-8 on my Velux shutter remote control to open and close it automatically with Homematic. Therefore i needed a new back for the Velux remote control, including the Homematic HM-MOD-Re-8. ... It's very simple...

Designed and constructed in 1966, the RF-4 is equipped with a retractable monowheel housed within the fuselage's center, along with a small tail wheel for steering and outrigger wheels to maintain wing balance. In May 1969, an RF-4D crossed the...

Fixing a Homematic switch requires securing the base with a M3x10 screw, followed by attaching the lid firmly.

Install Homematic IP Switch securely by fastening it to its case using three M3x10 screws. ...Be mindful of the electrical current, as handling it poses a significant hazard – exercise extreme caution when working with it, and do so at your own peril.

Accurately install a 1 x 2, 150# RF pressure relief valve; its mounting dimensions correspond to those of the Taylor 9300 series. The pilot's mounting height is the only specified dimension. ...This valve can be used in intricate 3D piping...