honda crv keychain 3d models
109301 3d models found related to honda crv keychain.myminifactory
A handy removable change holder that fits nicely into the compartment under the armrest of a Honda CRV mk4.
thingiverse
Recently, I purchased a 2018 Honda CRV but hated both available mounts, so I designed my own in Fusion 360. I was learning Fusion 360 at the same time which is why there are two design methods (split and All-In-One). ... The second AIO design has a...
thingiverse
This is designed to replace the factory switch blanks in the dash of a 2002-2006 Honda CRV, for the purposes of mounting an auxiliary switch for things like light bars, fans, etc. ...This is a flat blank which will mount flush with the dash in flat...
grabcad
This is a collaboration of information I have gathered on the internet as well as a physical study. ...it is a lift spacer for Honda crvs 1 generation
thingiverse
Pieza adaptador tapa para surtidor limpia faros Honda CRV
thingiverse
Frame to adapt 6-inch speaker for honda CRV 2008-2011
prusaprinters
The temperature control dial cover broke on my moms 2013 Honda CRV, so this was made to cover up the bright light underneath.
thingiverse
The little clip to hold the bar that is used to prop up the hood (bonnet) on my Honda CRV. Designed to simply clip into the square hole where the old clip fitted. ... Works very well - updated file has a better defined clip mechanism to hold the clip...
thingiverse
Car (2006 Honda CRV) had a dummy mount for XM, and the factory antenna is not made any more. This fits a Sirius XM SV300 antenna, and bolts directly to the holes in the roof of the car. ...Uses M4 bolts and screws into the plastic.
thingiverse
I had a wiper reservoir that had a broken cap on a 2001 Honda CRV. I could not find a good design so I made my own. If you still have the dipstick, you can zip tie it to the end. I make lots of custom designs for prototypes, etc. Please see my...
thingiverse
Replacement hubcap for my Honda CRV How I Designed This Designed to print using aquasolve support for the indent and Honda logo on the front (underside of print). Use silver filament for the print. Keep an eye on the print while doing the support,...
thingiverse
This is a cell phone holder for a Samsung Note 8 and a 2020 Honda CRV EX-L. With a phone in the holder it does block the hazard light switch but removing the phone gives you access to the switch. It also allows air from the vents to get to the phone...
thingiverse
A while back I changed out the sway bushes on a 2004 Honda CRV. The replacement bushes I used were Urethane. However I had to buy generic ones and cut them down with a knife to make them fit, as there are none available here for this model Honda. ...
cults3d
Designed for my 1997 crv. could work with others. sits in the rear light trim and is doublestick taped in. ...(3m foam tape)
thingiverse
2004 Honda CRV Windshield Washer Reservoir Cap
thingiverse
2002-06 Honda CRV has a poor cup holder design that causes drinks to tip over during a turn. ...This attachment fills in the empty space to hold drinks in place.
thingiverse
This is a simple print to give you a couple extra places to hang your shopping bags for Honda CRV Second generation (2002–2006). It prints without support - I used PLA. Just take the headrest on the back seats out and it will slide over the metal...
thingiverse
I made this latch to replace the broken original one from my 1999 Honda CRV. It was made to be glued over the remaining plastic on the cable from the original latch. It fits with a small interference above it. The latch is to be pushed down to the...
thingiverse
The Wiper Fluid Cap on my 2000 Honda CRV finally cracked and fell off, so I used the freeware version of eMachineShop to design a replacement. The Wiper Fluid Cap has a center hole in it so you can zip tie it to the long plastic piece that slides...