hot air station 3d models
121932 3d models found related to hot air station.thingiverse
Organizer for the inexpensive hot air station that seems to be everywhere...
thingiverse
This thing is a DIY hot air station to smd soldering. Is composed by hot air gun, an diy electronic card, an Arduino nano, an dc dc booster, an 12V PSU an REX C100 PID controler with SSR relay. The Arduino code and the electronic card wiring is...
thingiverse
I recently received my new Hot Air Rework Station 858D and needed a place to store the nozzles. ...The thing can be screwed to the stock blower holder and works just fine for me.
thingiverse
Horizontal Holder For 858D Hot Air Station This is a bracket that fits the popular 858D Hot Air Station. It is branded variously as JCD, Baku, Yihua, Txinlei, Feita, LRT, among others. The bracket that comes with the station holds the tool in a...
thingiverse
These are all of the parts of a Yihua 8858 Hot Air Station. The controller case is just a model an not printable. The collars would probably melt if actually used. The important part is the wand holder. The wand holder can be attached to the original...
thingiverse
Hot Air Station Organizer Organizador boquillas pistola aire caliente imprimir en solido para que sea fuerte la estructura.
thingiverse
Replacement holder for the gun of a hot air solder station. ...Designed for model 858D, but there are many similar models this will work with.
thingiverse
Toolcraft hot air SMD station nozzle rack. ... Mount with double sided tape to keep the nozzles together with the hot air station.
prusaprinters
A remix of the LTT Hot Air Rework Station Tip storage rack design to adhere to the rework station. ...Designed to hold 4x 22mm tips for the 85x series of hot air rework stations.Prints support free with the flat (back) on the print bed.
thingiverse
I made this for the replacement of the way to big housing of the 858D desoldering Station This replacement reduces the depth of the housing to around 10cm Just for replacing the body!!!
thingiverse
I didn't like how the station didn't have a good way to sit on my desk found the case by wisestone but the LCD board is in a different format so I re-made the case. ... TXINLEI 8858 used: https://a.co/d/7nnrGr9
thingiverse
I designed this so I could use my hot air gun hands free.
prusaprinters
The hot air wand holder can mount on the original base or be mounted separately as needed. If you install the magnets is will allow the station to automatically turn off when the wand is in the holder.The wand collars are not threaded and may not fit...
thingiverse
I made mine in TPU so the holder would have some give as the nozzles press on. ...Plastics should be okay too. And I used hot melt glue to secure it.
thingiverse
In case your Panel Holder Plastics also come with a crack because they tightened the screws too hard There are two stls, one has sacrificial bridges so the result looks cleaner without supports
thingiverse
Four of these spacers are required to install my replacement board for the Best BST-863 hot air station as seen here https://youtu.be/_PKAgJuqW78?t=320 These spacers come included with the board but I'm providing the file here in case someone loses...
prusaprinters
Just the tips -- a rack for 8x 22mm tips for the 85x series of hot air rework stations (We use the 858D) Prints support-free The diameter of the protrusions is 22.3mm on the main file because the nozzles measure out to that when new, and remain that...
thingiverse
If you need a stand for the KSGER hot air rework station wand and bought the little stand that Banggood sell, and don't want to drill into the case to fit it, and fancy something freestanding...then this may be of interest to you.... ... I have done...
thingiverse
If you want you can always appreciate and support my work, I will be grateful, below link to Donate. Thank You. ... https://www.paypal.me/bigvlad
thingiverse
Nice for Soldering / BGA reballing / Desoldering
thingiverse
My unit is close to the wall during cool down I was concerned the paint would start blistering as the hot air was directed at the wall. This bracket fixes that problem by blowing the hot air straight up instead. Simply remove the existing bracket...
thingiverse
First flatten the lamp's mounting plate, then use the original M3 bolts and nuts to tighten the mounting clamp.
prusaprinters
I wanted to save space and put my Ersa station on the 858 hot air station. Print instructionsThe adapter plate was printed in PETG and mounted with relatively thick (~1mm) sticky tape.
prusaprinters
Simply print on FDM or resin printer and use double-sided tape to fasten it to the body of the station.
thingiverse
... soit pas fourni... ...Compatible avec cette station : http://www.gearbest.com/soldering-supplies/pp_278636.html#lkid=10249282 This support help to avoid losing the 3 nozzles supplied with the station, it is a pity that the storage is not provided ...
thingiverse
Link do projektu https://www.hackster.io/makerbr555/diy-smd-rework-station-28b6f5?utm_campaign=new_comment_for_project&utm_medium=email&utm_source=hackster
thingiverse
... shown. Also usable for other solder stations that use the S208F hot air gun but may need some changes to the mounting geometry. ... Also checkout this part if you use this rework station (Not my design): https://www.thingiverse.com/thing:4763909