hot end temperature calibration 3d models

Remixed fan shroud added a text vent (style points) and reinforced the parts that attach to the hot end with hopes that it would provide a uniform surface for the stock BL touch mount angled the opening for a little more aerodynamics (probably a...

I have not been using a part cooling fan lately and have not had any issues so i designed a minimal lightweight hot end mount. I may design a compatible part cooling fan part when the need arises. Uses the original m4 hardware to mount to the...

2x from the CR-Touch, 1x from the existing fan shroud and 1x from the 4 bolts that are used to attach the hot-end to the X-Axis bracket. (3 screws are more than enough to keep it secure). Screw the CR-Touch into the shroud and route the cable using...

A custom mounting plate designed specifically for the Chimera/Cyclops clone hot end from FLSUN is now available. This plate seamlessly integrates with MoonDoctor's x-carriage, which can be found at Thingiverse under the ID 2553911. Although I still...

http://www.thingiverse.com/thing:1365834 A word of advice after configuring Slic3r for the new hot end: We had the 2011 model with the .5 nozzle so a lot of Slic3r settings changed when we moved to the .4. Slow down the first layer way down. We were...

Hence this remix, which is a combination of the [Anycubic Mega Zero v1.0 Hot End Shroud](https://www.thingiverse.com/thing:4863391) and the Aperture version of the [Customizable Fan Grill Cover](https://www.thingiverse.com/thing:2802474). Of...

You can reroute the hot end wires behind and through the belt holder. This setup has been thoroughly tested and fitted, making it compatible with the Anet A8. To ensure proper installation, print the X motor mounts from Thingiverse...

I adapted Blinkingsun's hot end mount to integrate existing part cooling fans from Thingiverse, specifically: https://www.thingiverse.com/thing:3446017 and also compatible with https://www.thingiverse.com/thing:3507515. To make this possible, I...

the height which the hot end sits was 3mm too high. also the counter bore for the screws was too deep.&nbsp;</p><p>Added 3mm to the mount and made the counterbore interface area 3mm thick so a 6mm screw would work. &nbsp;Also included a simple 3mm...

After converting my Anet A8 to the AM8 I maxed out at 160mm to avoid pulling on the Hot end wires. The device allow you to mount a 2x2 level nut to the frame:...

My version of a mold for a Dremel/Flashforge and possibly other mk10 style hot-ends. I use Red Permatex high heat RTV and it's worked quite well. The trick I found that made all the difference is dipping both parts of the mold in diluted Dawn dish...

We're using E3DV6 support for a cooling system that works with extruded material, paired with a 50mm tangential fan and a hot-end body cooling system featuring a 40MM fan. Print Settings: Printer Brand: RepRap Printer: Prusa P3Steel Rafts: We...

Hot end fan shroud for the Ender 3. Designed to accommodate my BLTouch clone plus a 4020 fan. I tried a few other designs here but didn't like any of them. I've been using this for over a month and it works flawlessly. Printed PETG. Minimal...

This text concerns Alu-Dual Hot End & Cooling Block Upgrade Spacers for the Replicator 2X, which should be printed prior to the upgrade. For a stock setup, Carls recommends a 3.5mm spacer, while 2.4mm spacers work well with the 3 in 1 extruder...

Remix6: Improved cooling on heat-sink for hot end. Remix7: Same as Remix 6 without LED lights, leveling sensor, larger fan ports, or manifold bolting feature. Remix8: Same as Remix 6 minus sensor holder, larger fan ports, LED lights, and ability to...

The concept is that it will obstruct some airflow coming from the bottom of the fan, thus not cooling the heater block, and you might even be able to run without a blanket on your hot end. ...If you're 3D printing it with ABS recommended, although with...

The user is utilizing a 40mm fan duct specifically designed for the Chinese E3D v6 hot end. Print Settings are being employed to optimize print quality and efficiency. Printer Brand is RepRap, with the Kossel Mini model being utilized. Rafts are...

Simply bolt the mount and nut block to the slider, then mount the MicroSwiss hot end and the Nimble. This is a really simple mount. The STL models have been checked and optimized. The parts that need a different orientation to print properly are...

The hot end LED light from Printermods.com is quite bright, too bright perhaps. I made this little diffuser that pops on over the LEDs (friction fit) to make it a little less bright. This is designed for if your wires go off to the right as you...

I have replaced the small part of the holder in order to mount the new heat break cooler.I got pretty tired when I had finished drawing up the heat break cooler so the camera mount is pretty hastily designed but it's quite rigid and stable.The nozzle...

I made a new version of the fan duct for cooling my E3D Hot End, based on the one designed by euphy that's available at http://www.thingiverse.com/thing:120249. My original duct had a problem - it got too close to the heat source and melted at some...

adaptateur pour installer des ventilateurs noctua 40x40 sur le hot end de la ender 3 max, il on été prévu pour installer un crtouch. Sinon il suffit de reproduire la symétrie de celui qui na pas la fixation, Mettre des supports partout avec un angle...

Once you've disconnected your outgoing hot-end from everything, the following things need to be done (WARNING, not a lot of detail here but I wanted to get something down quick for now) * The black bracket on top of the strain sensor (the thing with...

use adapters supplied in extruder kit to attach to Mosquito hot end modular mount using a short Teflon liner supplied in kit,shim BL Touch using a 2 mm shim and adjusted Z offset for first layer adhesion without elephant foot. ...Mine was .56mm adjust...

This is a remix of the hot end design and it makes the good design better, It allows for all the fane to be slid in and does not require any screws. Print Settings Printer: Alfawise U30 Rafts: No Supports: Yes Resolution: .2mm layer height Infill:...

I've been printing without a part cooling fan for a while now, and I haven't encountered any problems, so I decided to design a minimalist hot end mount that's super lightweight. I might create a matching part cooling fan part if the need arises. ... ...

... to carefully bend my X endstop out slightly to get it to trigger (fixed in v2).\n Printed at 40% infill, .3 layer height.\n Printed with support for the end stop wall. ...Rotate the clamp 180 degrees inside of the hot end interface is pointing upwards.

The steps to install a new fan and resistors for extruder heating in a 3D printing hot end are detailed, starting from disconnecting wires for the fan. Remove any unused connections to create space. Tighten exposed screws. Replace the duct assembly...

The wires to the hot end, fans and probe sit behind the stepper motor but there is nothing to really keep them in place. Sometimes the wires can slip out and it's possible for some to get caught between the extruder and the end bracket when the...

Resource files to help designers making modifications to the CR-10S Pro gantry, hot-end, or adding other options. Added additional details to the original provided by ValleyBot. With his original and my updates I was able to bring the popular Hero Me...