hovership mhq2 3d models

ASSEMBLY INSTRUCTIONS: Available Online at: http://www.hovership.com/guides RECOMMENDED CONFIGURATIONS Full Component List (BOM): http://www.hovership.com/guides/mhq2-build-components-list/ Beginner pilots and lightweight FPV with a Mobius or smaller...

Increased the height of landing gear to place a 4S battery at the bottom (still working on it!) No change in arms Here's the first flight video link: https://www.youtube.com/watch?v=KGaU51msiHU The vibration dampers I ordered from Hovership were too...

ASSEMBLY INSTRUCTIONS: Available Online at: http://www.hovership.com/guides RECOMMENDED CONFIGURATIONS Full Component List (BOM): http://www.hovership.com/guides/mhq2-build-components-list/ Beginner pilots and lightweight FPV with a Mobius or...

this is my hover ship MHQ2 http://www.thingiverse.com/thing:511668 pictures of completed quadcopter to come Files added: 35mm spacer 7.5mm washer landing gear that hold zippy 1500mah lipo battery

Hovership MHQ2 Quapcopter from hovership.com

I created a simple lateral air guard fot the Hovership MHQ2. If someone have some ideias share with me so I can design it. You need: 6 x 3M screw's. ...Print Settings Printer Brand: MakerBot ...

Clips I made to hold my hobby king zippy compact 1500 35c LiPO to the bottom of my hovership MHQ2. I need to get my CG more centered since I do not yet have a camera set on the front to balance things. Velcro straps were not doing it. They snap over...

Flight compilation video: https://www.youtube.com/watch?v=vrj7iZE8P1M Printed kits available at: http://shop.hovership.com/hovership-mhq2/ Hardware kits available: http://shop.hovership.com/mhq2-hardware-kit/ Power system:...

Simple Taranis and Taranis Plus Icon of the MHQ2. ... Download and rename: Hovership_MHQ2.bmp.eps to Hovership_MHQ2.bmp

Wanted a way to make more room for my battery on the bottom of my Hovership MHQ2, so I designed these to bolt onto the bottom of the motor mounts. Pretty pleased with them so far. ... To install these, you'll need to use 10mm or 12mm M3 bolts.

Simple Mobius Camera Mount for the Hovership MHQ2. A short video of the MHQ2 in action (with a Naze32 board): https://www.youtube.com/watch?v=dqG_FWd2Lpw Use different spacer lengths in front and back to reach the desired angle. ... 2 versions...

MOBIUS MOUNT TO HOVERSHIP MHQ2 I build a mount to protect my mobius. R2 that is strait. Also included a 5 deg. version. Remix of http://www.thingiverse.com/thing:564958 scaled down in height and opened up the hole for the interface plug. I merged...

Low profile landing gear for the Hovership MHQ2 Instructions mounts directly to the stock landing gear location

A mounting strap to affix a gopro/sj4000 style camera to the camera slot on the front of the hovership mhq2 multicopter. ...I printed this using SainSmart TPU.

This is a battery compartment and legs that fit the Hovership MHQ2 kit. It allows for a velcro strap to be used to hold the battery in. Still a work in progress. ... Thanks

This is a FPV tilt camera mount for the excellent Hovership MHQ2 by Hovership (http://www.thingiverse.com/thing:511668) inspired by the great tilt mount design by fragminiz (http://www.thingiverse.com/thing:507636) and toto...

Mount for a Fatshark 600TVL FPV camera on top of a Hovership MHQ2. I wasn't able to find a good camera mount for the MHQ2 so made this one to fit. Take advantage of the threaded lens and ring to secure the camera onto the mount, then use the existing...

... M3 lock nuts and 2 M3 x 10m screws. You will need to drill 2 mounting holes in the MHQ2 lower base plate. Instructions Printed with ABS at 0.2mm Layer height with 40% infill. ...No supports needed.

EDIT: 1-24-15 -Added an integrated spektrum satellite receiver mount called "clean lower Sat Mount.STL" EDIT: 6-1-15 Added STLs that are cut in half to print on beds ~125mm or bigger Instructions Uses stock 35mm spacers and m3 hardware from the...

This is a FPV Cam Mount designed to fit in the hexagon slots on the MHQ2 Clean Plate. I designed it with a 10 degree tilt . It also has a hole for a 4 inch zip tie so that you can secure it to the Clean Plate. It was designed to fit a Sony Super HAD...

I created a simple XT60 plug support for the MHQ2. To be honest I was inspired by some models already made, the problem of the already created XT60 plugs was that no one left me completely satisfied because some models are already incorporated on...

My friend asked if I could make a bit stronger landing leg for the MHQ2. I added a radial hoop between the feet that still allows it to be flexible but changes the load path enough to make the the braced corner not snap easily. Adds 3.3 grams each...

Spacers for the Hovership MHQ2 design. ...Just print and use a M3 screw to create threads.

Decided I need a bit more protection for my lipo hanging from the bottom of my hovership. Fits the zippy 1500ma 35c battery. Instructions Built on end without support. ...Make 2 they interlock from...

Quick mount box made up for my hovership to contain a 200mw transmitter. ... Instructions Built with support under the clips (this allows to get the TX far away from everything else as possible).

... this project here. http://www.thingiverse.com/thing:720556 Only these 3 parts are needed. Everything else comes from the original MHQ2 project. ... I modified the lower clean section slightly to help snake wires and components through.

Clip onto Hovership MHQ2 to hold down FrSky_V8FR-II Plus Receiver. I added ~3mm of foam under for cushion. ... Instructions PLA 25% .2mm layers 3 top 3 bottom 2 shell

hi this is a add on to the quadcopter hovership i bought a power distribution board and it was to big so i designed a way to integrate it too the quadcopter the board i bought was a "RC QuadCopter Power Distribution Board KK & HK Tri Heli XT60 3.5mm...

The folding arms always caused me problems on my Hovership, if I crashed or landed hard, the front would fold in so I would have to go pick it up and straighten out the arms again, and furthermore, the arms were never evenly spaced (not extended...

I embossed the hex's and angle at the front of the MHQ2 body. It fits tight so as long as it is held in place vertically the camera is not coming off. The stock go pro screw will have to be changed out for a standard head screw (i yet have to go to...