how to change filament ender 3 3d models

I've created a design for a filament guide and lead screw protector that uses a PTFE tube to eliminate wear on printer parts where the filament comes in contact with them. To use it, get a 25mm (1 inch) PTFE tube and slide it into the hole as shown...

1) Increased to102% for tighter fit (you may need to adjust for your printer and filament) 2) Added a clip in insert (my own design) that rotates so filament cannot fall out yet can when you align slots can be removed. 3) Added captive T Slot M4...

To create a filament runout sensor, use a holder for a limit switch. Cut the middle pin of the switch and then solder pins 1 and 3 to a cable. ...Finally, connect the cable to your printer, as shown in the last picture.You may need a longer M3 screw to...

redesign of my first filament guide with a longer filament slot to hopefully help with the filament catching or getting stuck if it is kinked or twisted on the roll, plus it looks cooler then the first.

I build this to help center the filament since the gap between the filament reel and the shaft of the native support is too big.

Needed a top rail filament guide, allowing me to print as highh as possible w my direct drive/filament sensor printhead.

This rugged end-of-filament sensor mount stays rock-solid even when subjected to intense retraction forces or the strain of a tightly wound filament spool.

UPDATED (4.06.2021) - Improved TIGHT FIT to printer frame Simple filament guide - Easy snap in - No supports - 1.75mm filament

this is a snap on bracket for the ender 3 v2 3D printer for the mosaic palette 3 pro. as far as I know it should fit all creality stepper motors. ...push down from top corner of z motor and it should slide right on til you hear it snap into place.

It fit with oryginal spool holder Ender 3 pro Use PETG material if you use heated chamber. ... Infil 100% Minimum 3 wall line count Use Brim Bed temp: 65*C Fan speed: 10% For Nozzle 0.4mm: Nozzle temp: 230*C Layer height 0.3mm Line width 0.5mm Speed...

My Endless 3 Spinning Adapter for Filament Rolls with a 75mm Inner Diameter, used with: https://www.thingiverse.com/thing:3421762

I designed this simple guide so my filament filter doesn't mess with threaded rod. ...I designed 3 versions with different gap position and 1 without any gap.

you can replace this with the cap of the original spool and have a double spool as well, its width is 3 cm so any filament can fit

... in one of the photos. My switch dimensions were:12.8mm long, 5.8mm thick, 7.15mm switch collapsed. When soldering switch to connector, be sure to have your orientation worked out.The bearing guide cover was used from another bearing filament guide.

I did it because I never know where to leave the filament I don't use.

I did it because I never know where to leave the filament I don't use.

Stronger version of https://www.thingiverse.com/thing:3059604 Ideal to mount under the filament holder. ...

i wanted a longer guide to get the filament going in better. ...

I designed this to be used with the runout filament sensor from AliExpress

Small shield to keep the filament from touching the z-screw.

Guide to prevent filament from touching Z-rod on feed/retraction. ... Print 100% infill, no supports

Another version of the same filament guide where the funnel is much closer to the extruder.

Remixed to allow 45deg offset for smoother filament flow from spool.

The filler mount fits in the stock spool holder arm for the Ender 3 S1. It works really well for me whether for the left side or the right side . EDIT : Now 2 versions are available, the first for a reel diameter ranging from 35mm to 60mm, the...

Ive created this minimalist filament guide to help support the filament coming in from my [Side / Rear Spool Mount](https://www.thingiverse.com/thing:5237821). It bobbles with the back and forward movement of the filament but still holds strong for...

My replacement part swaps out one base piece per side and enables you to connect both roller assemblies to the side of your Ender 3. The tabs slide smoothly into the lower extrusion channel, and if desired, you can also secure them using the factory...

I've modified the original STL file to incorporate 2 F695-2Z-EZO rollers that guide filament without noise. The original one sometimes makes cries when the extruder retracts as the filament touches the edges of the hole. List of materials needed: 2...

I have redesigned the same model with some modifications to fit my smaller bearing and also with a ENDER embossed Text instead of some grooves. ...Inspired by this user.

Split roller bearing to support a spool of plastic on a standard holder.UPD: added a bearing model with only one cut with an outer diameter of 52mm, an inner diameter of 30mm for a standard Ender holder.

I've reworked the design to suit my narrower dimensions, incorporating an ENDER inscription where the previous grooves were located. ...The idea was sparked by another user's innovative approach.