how to change filament ender 3 3d models

This design serves three purposes: it provides protection to the exposed bearings for the z-axis screws (no dust accumulation, filament fragments, etc falling in), provides a filament guide for those that aren't using the on-body spool holder that...

This bushing gets rid of the "slack" due to the size of the center of the Overture spools and will allow the extruder to more freely feed filament. ...It is a little tricky to slip over the edge of the holder, but once on, the spool will very easily...

... job. Its simplicity makes it easy to use, even for beginners. The filament is specifically engineered to work seamlessly with most standard FDM printers. ...By reducing the need for post-print processing, it saves time and increases productivity.

One thing to keep in mind is that reel diameters can vary depending on the specific manufacturer, so it's always a good idea to verify compatibility with your own brand of filament before proceeding. ...Could you please review the attached design for...

A quick small filament guide i made on fusion 360, I didn´t research to much on other kind of guides, so i recommend this just to start, or if you dont have too much filament cause there are other more complex that do the work much better. Feel free...

It can prevent friction between the filament and the extruder/Z Axis, and reducing the area exposed to moist air. ... * With M6 thread, M6 Fittings(I'm using KJH04) can be easily install * Simple installation, no tools required * allen_wrench.stl is M6...

Remodeled from scratch but heavily based on fredkylam design, the problem I faced with his design was that when the gantry was too high, there would be no slack for the filament to feed into the extruder when the carriage was positioned more towards...

Simple remix to accept filament from below rather than above. https://www.thingiverse.com/thing:3052488 Print instructionsCategory: 3D Printer Accessories

Holder for filament spools with an inner diameter of 5 cm. ... Made in PLA. To reduce the friction of the spool you can add skateboard bearings that fit and reduce the friction produced by the drag.

Wasn't completely pleased with the security of some of the press-in style filament guides and I needed a different length and angle to work with my enclosure.

Extension for second spool. ...Fits for the original holder, if you use a dual extruder or for fast filament changeFits with bayonett lock to my spool holder: https://www.thingiverse.com/thing:5502057

I created a straightforward tutorial to ensure my filament filter doesn't interfere with threaded rods. ...The guide features three distinct designs, each with a varying gap placement, as well as a fourth version that omits the gap altogether.

This is a cover for the x axis stepper motor with slot for capricon tube to guide filament from the front of the printer. ... i have this paired with this design here https://www.thingiverse.com/thing:3419659

I designed a custom-made filament sensor because none of the ones available met my standards. The installation process is straightforward, taking only a couple of minutes to complete. ...It's now ready for printing.

... movement of the spool. To enhance efficiency, I applied polyurethane foam to the contact surface. The brake has proven particularly effective when printing in the uppermost position - the filament remains on the spool due to being under tension.

I saw the excellent Filament Guide by POEPOEFRED but when I printed and used it for a bit, it broke.I then decided to design my own guide based heavily on the one by POEPOEFRED.

This device features a filament guide equipped with a wire presence sensor and a three-pin plug socket that can accommodate a power cord, providing crucial support to the extruder.

V1 - Subject to improvementMy lazy attempt at meshing these two filament guides together, hope you enjoy :)Was a tight fit with no prep work at the base of my spool holder

... was tailored for the stock printer height. Since the Winsinn intake is positioned 17.5mm away from its mount, I decided to modify it using Tinkercad to better suit my needs. ...Meanwhile, the Bowden tube openings are precisely 4.25mm in diameter.

filament guide and sensor relocate when not using the filament sensor

... au centre et ne touche pas le bord du levier. J'ai aussi intégré un support de câbles. With this filament guide you will be able to print these great objects: https://www.thingiverse.com/thing:4853538 or https://www.thingiverse.com/thing:5004757

... au centre et ne touche pas le bord du levier. J'ai aussi intégré un support de câbles. With this filament guide you will be able to print these great objects: https://www.thingiverse.com/thing:4853538 or https://www.thingiverse.com/thing:5004757

That brings us to version 3 - this guide perfectly guides filament into the extruder without needing additional guides near the spool. There's a slight bend as it exits the tube into the extruder, but I haven't noticed any issues so far. Depending on...

No screws, no supports, 608 ball bearing filament guide designed to fit in the Filboyt filament guide mount. Combine with thing:4683505 (lower) for a complete the set of no screws, no supports, upper & lower filament guides. ... In the pictures the...

I'm sorry about the terrible print job; this filament is really giving me a hard time.\r\n\r\nIt's probably because my filament holder wasn't properly aligned, which causes certain spools of filament (like the one I'm using now) to get stuck on...

This is a simple, single printed piece filament guide that allows the insertion of the filament in the correct position and angle, without rubbing against the Z spindle. Apart from the model to print, these elements are needed: 1x 20T GT2 smooth...

I designed my filament sensor to be mounted right next to the extruder, ensuring maximum proximity. Using 100% infill with PETG was essential due to this part's structural importance. ...Credit goes to "kelokera" for handling the most challenging...

In this quick video, learn how to construct an assembly and apply base placement constraints in PTC Creo Parametric 3.0. Thanks to Christian for sharing his Lego Technics 42007 model. ...Find more tutorials and animations on the 4Kside homepage...

I've seem similar roller guides but I wanted to design one that will let me remove the filament from the roller without having to unload the filament from the hotend. This allows me to remove the roller while loading the filament if it's giving me...

Based on the Reinforced Ender3 Spool Bracket by macnickers on Thingiverse: https://www.thingiverse.com/thing:4666741I really didn't want to use an additional bracket to turn my spool sideways so I extended the base and added reinforcement with...