how to thread a pfaff sewing machine 3d models
2870160 3d models found related to how to thread a pfaff sewing machine.thingiverse
If I use a fresh big thread spool it won't fit in horizontally, so I need to mount it vertically e.g. with this http://www.thingiverse.com/thing:1922373 . But the thread may fall off at the downside and get stuck. So i constructed a guide for the...
thingiverse
Hello all, this time, my mother-(soon to be)-in-law came up with an ancient if not prehistoric sewing machine "Pfaff Type 1199". She claimed, the machine would work well, however the lever that elevates the stamp to hold down the fabric while...
thingiverse
I added a P to distinguish the parts easily. The factors are: 73% and 101%. ...Print Settings Printer: Renkforce RF100 Rafts: ...
thingiverse
... die Unterspulen aus. ...Kurzerhand habe ich welche gedruckt. Diese Unterspule ist für Pfaff 1501 konstruiert worden. My partner went from sub-coils . Without further ado, I have that printed . ...This sub coil has been designed for Pfaff 1501 .
thingiverse
I recently acquired a Pfaff 209 sewing machine that came in a hard case with a missing bottom part in the handle part. This makes carrying the heavy machine painful. ...This part fits snugly and makes lifting the case much more comfortable.
thingiverse
I just adjusted it quite a bit in order to get it to work on my Pfaff Triptonic 2030 machine. I printed 3 of them because it's all plastic and I was worried the cross bar would break the first time. I was thinking about removing the plastic cross bar...
thingiverse
(You'll need to disengage the Pfaff's walking foot.) Instructions Printed in PLA. I used 0.2mm layers, but finer would be better. You'll probably want to sand the bottom surface of the foot so that fabric feeds smoothly. ... You'll also need a 1/16"...
prusaprinters
You'll also need a 1/16" dia, 5/8" long steel pin. To lighten the pressure of the foot, I use four #33 rubber bands - two sets of two in parallel and then loop the two pairs together to increase the length. I then just hooked the open ends together...
thingiverse
Loop the rubber bands around the business end of the sewing machine and underneath the edge of the foot mechanism as shown. You can increase or decrease the tension on the foot by shifting where the rubber bands contact the body of the machine. ...You...
thingiverse
I use a lot of vintage sewing machines and tend to be disorganized, so finding my thread snips is sometimes a hassle. Newer sewing machines sometimes have built in thread cutting. So I designed my own. It uses a standard utility blade and two...
cults3d
small conical adapter to use thread bobbins designed for overlock machines (conical shape much bigger and cheaper than the classical bobbins) the goal is to be able to use these big bobbins on standard sewing machines with a 6mm bobbin holder shaft.
thingiverse
Large size takes 6mm rod, small size take 3/16” (roughly 4.8mm) rod Also 2 version of the Bobbin Wheel, large diameter takes 6mm rod, the other takes 3/16” (roughly 4.8mm) rod 1 x Central rod 8mm x230mm (longest I had) 2 x horizontal rods 3/16 x...
thingiverse
Hope will be useful for someone whos using sewing machine. ...
grabcad
Q&A link: http://grabcad.com/questions/how-to-make-square-thread-profile-with-specific-dimension-in-sw vote it! ...:)
thingiverse
Replacement carry handle for Pfaff 1209 sewing machine and some others in the 11XX / 12XX family. Instructions Printed laying flat, so layers run around whole handle. ...May need to adjust holes to...
thingiverse
Spool Holder for Pfaff 1199 (11XX/12XX) Sewing Machine. I broke it while working on in in our RepairCafe. ...
thingiverse
My Pfaff 332 sewing machine was missing the rubber feet for the extension bed. Here's a new design for the missing parts. On my machine one spot required a 'medium' foot, the other a 'large' foot. ... The only difference is the diameter of the post in...
prusaprinters
This is a replacement for a broken spool holder bracket for my Pfaff 90 sewing machine. ...It might fit on some other Pfaff models of the same vintage as well. Print instructionsI used PETG.
thingiverse
An extension for the sewing thread spool holder. ...Adjustable across the original spool holder. Specifically works for brother sewing machines, but will work for any shaft with a diameter of 5mm.
thingiverse
I made this to hold cone threads for my Embroidery Sewing machine, not a fan of the thread holders available in the market this design works for me. Its modular design enables to use 1 to 4 cones as required. and its easy to print without warping as...
thingiverse
The spool holder that comes with the Cobbler's Sewing Machine is too small to hold a cone of thread. This adapter fits on top of the metal rod and holds the cones of thread I have. I printed mine with PLA at 40% infill and has been holding up fine....
prusaprinters
My Juki HZL-357ZP sewing machine comes with some small thread and the stand for them. ...But I usually use bigger thread(3000yard version which is common).I print the stand to snap into the original Juki stand.
thingiverse
This should hold the coil of thread on my Chinese leather sewing machine. It has been otherwise getting stuck and tangled. I will print this in the morning and try to get pictures uploaded. ... I believe the pin the spool sits on is 1/4".
youmagine
If your Thread holder in your IKEA sewing machine breaks, then here you have a replacement part. I used slic3r and printed with the following parameters with good results. ... layer_height = 0.2 perimeters = 2 top_solid_layers = 3 ...
thingiverse
These widgets can be used to retrofit an old singer sewing machine with modern electronics whilst fitting in the old motors housing. The screwdriver mount will fit around a cheap cordless screwdriver and allow it to fit in the housing snugly. The...
thingiverse
This is a replacement thread spindle for the Singer 401A sewing machine