hpi blitz 3d models
1096 3d models found related to hpi blitz.thingiverse
... PITCH). ...Due to using support material need some sanding to fit the slipper clutch on the bottom side. I designed, printed and installed this gear on my HPI Blitz because my old spur gear teeth were damaged and after replacing all it's working fine.
thingiverse
This is a Front Chassis Brace for the HPI Blitz as Exotek has discontinued their aluminium ones, so I was unable to get one. When printed in PLA, the brace is very rigid, probably not as strong as the aluminium brace, but with added thickness, it...
pinshape
allows mounting Traxxas Velineon ESC to HPI Blitz with no drilling.
thingiverse
allows mounting Traxxas Velineon ESC to HPI Blitz with no drilling. Instructions Printed at .1mm resolution. ... 20% infill.
thingiverse
This is a Mk.1 ski kit for the HPI Blitz. This simple kit requires the acquisition of bolts to hold the spindle to the ski and a little bit of cleanup on the bolt holes on the ski and maybe some cleanup on the spindles for it to fit right. ...(sorry...
thingiverse
Here is the 83 teeth spur gear for the HPI BLitz and other vehicles using this slipper setup. ... For best restults print at higher infill and support.
thingiverse
Here is the 77 tooth spur gear for the HPI Blitz and other vehicles using this slipper configuration. ... For best results print with a support density of 25% and a fine resolution + higher infill.
thingiverse
This was whipped up out of necessity, it works pretty well I found but it helps to have good control of your truck. While I did only make the right side y'all can just mirror them in your slicer and have a left side too. ...Print Settings Printer Brand:...
cults3d
Cheap fix for your rc truck HPI Blitz and Blitz Flux mixed front parts Hpi103326 & Hpi86881 Hpi parts are hard to find so you can replace 2 of them with my creation Quick and easy to print Réparez votre voiture 1/10 RC HPI Blitz et Blitz Flux Pas...
pinshape
This clutch cover allows you to mount motors such as the Traxxas Velineon where the motor shaft is longer than standard length. ... Mount holes are tapered for drilling to correct size.
thingiverse
This clutch cover allows you to mount motors such as the Traxxas Velineon where the motor shaft is longer than standard length. Mount holes are tapered for drilling to correct size. ... Instructions...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: font_size = 10 Font = write/orbitron.dxf hole_radius = 3 message = Aze-t Blitz stick_width = 8 font_thickness = 5 stick_thickness = 3 flat_bottom...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: minimal_color_layer_thickness = 0.6 font_size = 12 font_narrow_widen = 0 character_spacing = 1.15 text_thickness = 4.2 outline_thickness = 3.0...
thingiverse
Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069
thingiverse
Customized version of https://www.thingiverse.com/thing:3094095 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3094095
sketchfab
Opel Blitz Truck. I used blue print and many photo references. ...AO textures are baked on auto pack UVs
3docean
Opel Blitz – German truck, the early models of which were actively used by the Wehrmacht in World War II. The grid is well optimized to reduce the load on the video. Moving parts are separated from each other in order to be able to animate the...
thingiverse
X - SIZE 8.7 !!!!!!!!!!!!!!!!! ...Front and Rear Bumpers and Simulated Front Off Road Lights (Part # 85059 Partial)
grabcad
hi, it's my HPI savage. i did everything except the engine. it's not finished yet. I still have inside of the gearbox and details. ...=) render with Keyshot.