hpi rs4 drift 3d models

This is a simple modification for the HPI RS4 3 Drift nitro car air intake. The factory fitted rubber pipe bend needs to be turned upside down and needs to face forward. A hole (size depends on air filter diameter) needs to be cut in the hood of the...

micro rs4 front drift tire. ... Just replace the rubber tire for this part.

2 wings and a diffuser for the HPI Micro RS4. The diffuser fits on the R34 body with some amazing goop/shoe goo(http://www.ebay.com/itm/151009278674?_trksid=p2055119.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT) and the wing fits on the HPI wing mounts...

micro rs4 rear drift tire. ... Just replace the rubber tire for this part.

The OE upper deck set has a battery tray post that can break causing inconsistent throttle response. This part was designed with the intent to replace the existing part after the battery tray post breaks. Please comment on any problems that you run...

Lipo Mount for HPI RS4 Sport RC Car 1/10

These are 3D models of all of the plastic parts found on the original HPI Nitro RS4. Most of these pieces can be used as direct drop-in replacements for the factory originals. All hinge pin holes should be reamed out with a 3mm reamer and all...

I was looking for a new spurgear for my HPI RS4 (single gear) but since the parts are not made anymore and my got ripped of all its tooth i designed a new one. i do recommend using supports. Recommend ABS becouse it can "bend some more" ...

... they don't get in the belt. Parts are likely able to fit other HPI vehicles, I found the lower control arms for my Rally appear to be close enough to the standard RS4 that the ones from this page will work: https://www.thingiverse.com/thing:4655433

It is a wishbone for an old HPI RS4. ...Part number for the complete suspension arm set "A450" from HPI Racing Es ist ein Querlenker für einen alten HPI RS4. ...Teilenummer für das komplette Querlenkerset "A450" von HPI Racing

This is a replacement spur gear for the HPI RS4 Evo3+. Its part number HPI 76817 (47T). It might fit other RS4's too. I don't have high hopes for this one but i literally can't find replacements to purchase online. I printed it in PLA with 80%...

Replacement upper Suspension support arms for the HPI RS4 3 evo+ (might fit other rs4's.) I decided to make thicker custom ones rather than design an exact copy of the originals from the car. You can view/download the Fusion 360 project here.

Drift tires and rims for HPI micro

This "tire" mounts directly on the wheel of a hpi 1/18 RC car

This is a replacement wing mount for a drift AE86 body for Micro RS4 from HPI. The original design requires you to bend the piece, so it's prone to break there. It seems the official replacement part is HPI #73405, which would comes with 3...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/fDybLzWuUAh

These are head- and rear light buckets for the micro-RS4 Ford Mustang from HPI (Justin Pawlaks formula drift car in Falken Tire livery). They use 4mm square white LED SMD chips for the head lights and 4x3mm red LED chips for the rear lights. I also...

Broke a control arm on my HPI RS4 Evo nitro 1/10 RC car. Modeled it on Inventor, printed out and installed on my car. Works perfect! ...No more waiting on extinct cheap plastic or expensive aluminum replacement parts from China if you have a decent 3D...

Vintage HPI RS4 Nitro MT has a removable radio tray, and these are the parts that hold it in place. There's a small round pivot for the back of the center tray. There are two of the flanged body mount pieces. These would originally come from the...

This is a remix of a Lipo Holder for an HPI RS4 Sport (a vintage 1st Gen version). This has been modified to add a small pulley to slightly raise the belt off of the LiPo case. Otherwise they would lightly rub so this hopefully prevents belt wear. ...

Drifting rims and tires for the HPI mini Recon. ...Put the rims in the freezer and shrink them down before you try to put on the tires.

Replacement Throttle Linkage for a HPI RS4s Nitro Star G3.0 engine. I recommend printing this edge down with supports as shown to avoid layer lines going horizontally across the neck of the part. ... **WARNING** PLA might not survive the heat of the...

Replacement Throttle Linkage for a HPI RS4s Nitro Star G3.0 engine. I recommend printing this edge down with supports as shown to avoid layer lines going horizontally across the neck of the part.</p><p><strong>WARNING</strong> <strong>THIS...

Caster angle 12° : perfect for drift no C-hub : the limit to steering angle is the CVD (and no limit in case of RWD) additionnal parts : 4 M3x16 screws 2 ball ends Ø4.8 (I used RPM 4-40 #73372 from asiatees...

Caster angle 12° : perfect for drift no C-hub : the limit to steering angle is the CVD (and no limit in case of RWD) additionnal parts : 4 M3x16 screws 2 ball ends Ø4.8 (I used RPM 4-40 #73372 from asiatees...

RC body rear magnetic mount (for HPI 1/10 RS4 RTR).

Will fit other models but made for HPI RS4 Evo. Drill your own mount holes. Reuses spring lid from original tank. Even has baffles to stop fuel sloshing like orginal tank. ...No primer!

Since wheels for the micro RS4 seem to be discontinued, I created some basic wheels that fit the HPI D Compound soft rubber tires. There is a center block support so that the tire foam stickers do not need to be used. ... Printed on Prusa Mini I...

Since wheels for the micro RS4 seem to be discontinued, I created some basic wheels that fit the HPI D Compound soft rubber tires. ...There is a center block support so that the tire foam stickers do not need to be used.</p> <p>Printed on Prusa Mini</p>...

... contact with the driving surface to greatly minimize traction. Not recommended for super slick surfaces. These Tires fit HPI LP series rims that have removable back rings for easy install. ...These will not easily fit other brands or types of rims.