ht radio desk stand 3d models

Very simple radio stand, usable for pretty much any handheld radio including Baofeng, Kenwood, Yaesu, Icom, Anytone and others. Just slide the clip over the top. v2 - Simple stand for smaller radios and standard antennas. v3 - I found those using a...

This desk stand allows you to drop a Baofeng UV-82C radio in it and keep it held vertically on your desk, similar to the charging dock but considerably more stable. ... This is the perfect accessory for using your radio with a lapel mic.

May 2020 From Randy - W4LKS ICOM ID-51 3D Printed Desktop Stand Here is a simple desktop stand that holds the ID-51 at a pleasant angle for viewing the screen while it sits on your desk. The base is wide enough so it would be hard for an earthquake...

I designed this so my RMM2050 wouldn't be so “tippy” when I set it down on my desk or other level, stationary surface.It has a single hole in the bottom so you can fasten the holder to your surface if desired.  Otherwise I recommend adding...

I also position one rubber foot to grip the HT clip on the back.(see photo) This made it much easier to adjust a good grip for different radios. In one case, instead of rubber feet on the base, I epoxied Sonicare toothbrush magnets in place of the...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3tcmi5sCkZg

This fits the Baofeng UV5R. ...Insert the belt clip into the top part and use the cup part for storage (headphones etc).

Stand for rc radio with uhf box fitted to the back.

A stand for a Kenwood TH-D72 HT to allow it to sit on a table and use a speaker mic. ... Also has a mount for a KES-3 speaker.

I build this stand for my taranis witch has a 5 mm wire handle but it will work with many others radios, it works great. if you print it please share your thoughts and pictures if possible, I'm currently working on a 250 quad I'll post it when I...

A "Handy Stand" for HT's. I designed this to suit my TYT MD-390, Icom ID-51 & 31 and my Yaesu VX5GR so it should suit most hand held transceivers. I could be modified to suit others if necessary. It was a 4 hour 27 minute print on my Anycubic I3 Mega...

This is a folding desk that straps to one leg for use in a field radio setting. When folded up it measures 8.5" by 7". When unfolded it is 8.5" wide and 14" top to bottom. In the top section there is a small recessed are in which one can place a...

ht

Soporte de radio para escritorio, es una leve adaptación a la versión original con vista al teclado y 3 extensiones en la base para darle estabilidad. ... Baofeng uv 9r plus

The space between radios allows for other HTs to be used as well, such as the Anytone 878 (fits right in the middle no problem), but you could pop anything in there provided the HT isn't wider than about 65 or 70mm wide. The slots for the belt clip...

Here's a quick make of a wall mount to hold 6 HT style ham radio antennas. You know...you get more 'Fengs, get Nagoyas for them, and have a bunch of rubber ducks tucked away in a drawer...well you know what? ...Those rubber ducks could be useful in...

I needed a project to help me learn it ;) I currently have a Baofeng UV-5R clipped to it, but it should work with most belt clip HT radios. I even made a coax clip which should help keep the cable tidy while using. It snaps tight and seems to stay...

I needed a project to help me learn it ;) I currently have a Baofeng UV-5R clipped to it, but it should work with most belt clip HT radios. I even made a coax clip which should help keep the cable tidy while using. It snaps tight and seems to stay...

I needed a project to help me learn it ;) I currently have a Baofeng UV-5R clipped to it, but it should work with most belt clip HT radios. I even made a coax clip which should help keep the cable tidy while using. It snaps tight and seems to stay in...

Might stand up to the warm car temperaturs better if printed with a different material however. Prints easily at 195 degrees. No supports needed, attaches to dashboard with a simple 3M Command strip. Update: Added a hook for a hand mic. ...

Stand gas soldering iron HT-B01

Stand for the Baofeng radios.

Stand for mcHF SDR radio.

It simply clamps onto the side of your desk. Desk thickness must be >17mm. Feel free to tinker with the file, it's really nothing special Instructions Honestly I threw this together in about 15...

A stand for my CB Radio

Stand for motorola radio DP4x\XPR7x series.

A stand for my CB Radio

Stand for a YouKits HB-1B QRP radio.

The stand can be used for other devices like HT radios. You will need to duplicate the number of parts needed for each project. Print Settings Printer Brand: LulzBot ...

The stand can be used for other devices like HT radios. You will need to duplicate the number of parts needed for each project.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>LulzBot</p> <p class="detail-setting...