htc vive stand 3d models

A simple holder for a Vive. ... You can either super-glue the attachment on to the stand or leave it interchangeable. I chose PETG due to its high durability. ...PLA will work fine too, but will become more brittle over time.

HTC Vive desk stand including controller and it is possible to charge the controllers while on the stand. Weights aprox. 350g and it is very stable, the base is 180x180mm and you need aprox 250x250mm of desk space to have this on your desk. ... You...

a 15 degree stand for the standard HTC vive basestation. I forgot to account for the rubber foot, so it doesn't fit flush unless put in upsidedown, but it still works perfectly fine. Since the part won't be under any stress, you can print at a...

A remix of the stand by andrewgodwin (http://www.thingiverse.com/thing:1547535) to get the files for them. ...Model rebuild in Autodesk Maya Print Settings Printer: LMNET - LM110 3D Printer ...

It fits into HTC Vive controllers stand by Animazu http://www.thingiverse.com/thing:1829212 It snaps in and then hold in place by pushing a little pice of paper in the resulting gap (as shown in the picture). I also added another inlet for a...

This is a modification of the vive controller mount from SG-O (https://www.thingiverse.com/thing:1443154). Make sure you go there to get the Base AddIn part you want to use.</p> <p>I modified it so that it would fit on the print bed of the replicator...

This is a modification of the vive controller mount from SG-O (https://www.thingiverse.com/thing:1443154). Make sure you go there to get the Base AddIn part you want to use. I modified it so that it would fit on the print bed of the replicator 2.

The stand file was broken where one of the controller stands met the base. ...I just layered the original headset stand over it to fix the error.

Hello Print 0.16 and enjoy ! [il faudra ajuster les trous permettant l'emboitement. ...Si besoin percer à Ø3mm-0.2mm+0]

I made this because i dont like my headphones getting bent by the headset when i lay it down somewhere. It supports the back of the headset where the spinny wheel is so the headphones arent bent or squished. ... use tree supports to save material

This is a stand for the Vive's controllers.It can be used as a simple stand or as a charging station. There are several add ins available that allow different Micro USB cables to be mounted in the stand to convert it into a charging station. If no...

A remix of the original stand by SG-O that takes two controllers back-to-back with minimal footprint. Takes the same cable inserts as the original; see that Thing (http://www.thingiverse.com/thing:1443154) to get the files for them. ...Print Settings...

The dual charging stand didn't have any inserts included in the files. The part that it was remixed from had some inserts, but they didn't fit when printed, nor did they fit the OEM cable :( This was quite disappointing, so I ended up...

You will likely need to rotate this onto it's front before you print it.

I printed out the [HTC Vive Desk Stand by Marcos10Soares](https://www.thingiverse.com/thing:2412007) and found my vive hmd was of a slightly different design such that the top part that holds the headset had nothing to grip to. They seem to have...

This is an elevated stand to hold base stations for VR systems that have base stations or repeaters like Oculus and HTC Vive.

Lighthouse stand to fix an HTC Lighthouse on a shelf. Angles the Lighthouse down 20 degrees. The camera is "held" in position by a lip on the front edge. Designed for a shelf of 18mm thickness. Print Settings Printer Brand: ...

The stock Vive straps will slip into the groove, but the wii clasps are too large for that. ...Print Settings Printer Brand: Printrbot ...

Stand for HTC Vive BaseStation. You can install the base station towards the UP or DOWN at an angle of 30 digrees. 30 digrees UP-mode is for installing the base station on the floor or near. DOWN-mode is for installing the base station on the shelf...

... ...&nbsp;It is HTC Vive themed but feel free to remix away.You will need to glue the strap support piece into the top portal and acquire two 8mm x 250mm rods to finish the build.&nbsp;Enjoy!Message me if you have any questions on the build.&nbsp;

... tip over in any direction. Print, pressfit, enjoy! :) OpenSCAD remarks: You need the "dual_vive_charging_stand_v2.2.stl" (not included in this thingy!) from the original design in the same folder as the .scad file to work with my hacked up openSCAD.

Starting in the last quarter of 2016, HTC started shipping controllers with a thicker blue strap, which also has a thicker clasp. ...To accommodate for this, I added a 0.5cm offset on the groove, which should allow it to easily fit any kind of strap.

Leapmotion stand for htc vive pro2.

Modeled to allow the HTC Vive standard wall fixture to go on alot of existing lighting stands, remove the light fixture and slap this bad boy in, bolt the wall fixture on top and you are good to go.

I have been looking for a solution to charge my Vive trackers in conjunction with my Trackstraps Plus. Unfortunately I have not found anything. Therefore, I have tried to do something myself. With this solution, you no longer have to charge the...

I wanted a desk stand to go with my batteries. ... I mixed a couple different ones together to make this.

Thanks to the original designer! This version has much more room for the theally big plastic parts of the WiiU straps I used to replace the originals with. ... Enjoy :-)

These here are some simplistic Charging Bays for my Index Controllers and also my new VIVE 3.0 Trackers. I didn't like how all my VR Gear was just laying in my Drawer so i decided to get it all a bit more Cleaned up ^^ I Recommend using Magnetic...

Oculus Rift or HTC Vive headset stand

... and shortened it from the bottom. ...So the whole thing is 27.5mm high and therefore fits into the [HTC Vive Desk Stand](https://www.thingiverse.com/thing:3560427) 28mm hole without any problems.