hubsan x4 frame upgrade 3d models
133753 3d models found related to hubsan x4 frame upgrade.thingiverse
A simply and light frame it can be used with hubsan x4 electronic (7mm motors).
thingiverse
Replacement frame for my hubsan x4 that I broke. ...It ended up being about 25% lighter than the original one, and feels sturdier.
thingiverse
This is a 6.5 gram frame specially designed for hubsan x4 h107L but it would work just as well for any other micro quad with 7mm or 8.5mm motors. This frame was built to be sturdy yet lightweight (less than half the original frame's weight). This...
thingiverse
Another replacement frame for the Hubsan x4. Inspired by some of the other frame designs but with a few improvements, including stronger feet and a battery clip. Comes out weighing a few grams less than the original frame, but feels very solid. ...
thingiverse
This is a replacement frame for a hubsan x4, I hope to print and test over next couple of days. still need to design a top cover. battery will need to be held in place with rubber band or velcro until I think of a better way :) update: new...
thingiverse
This is a frame that accepts Hubsan X4 micro quadcopter guts. Motor openings may need to be manually enlarged based on printer settings. All models should be complete solids now. Versions are in order of apperence above. These frames are designed to...
thingiverse
This design is slightly wider than the original Husban X4; between rotors: original 65mm, mine 101.6 mm. This lends itself to a better hover and more controllable through turns. I added landing gear. These also serve as a place for a 500mAh...
thingiverse
My original Hubsan x4 H107 micro cuadcopter frame broke, so I designed this frame as a replacement. ...This frame has been set to fit all the original parts.
thingiverse
My hubsan x4 crashed and the frame broke. This is a repalcement frame I created, it's obviously not as durable but very light and highly replacable :) It is built for 7mm motors. ...Print with 100% infill for maximum strength.
youmagine
An idea borrowed from "Micro quad v1 remix for Hubsan X4" by mouserunner.Rotary slot pattern should accommodate Hubsan FC, as frame design is symmetrical, FC can be mounted facing either axis. Slot standoffs on top are meant as support material...
thingiverse
Wanted to make a Hubsan x4 frame that I could print in one piece on my Anycubic Photon. Fits nicely on the bed if you tilt the model to a 45 degree angle. Be generous with the support material as I had a couple of droopy corners the first time I...
thingiverse
This drone has been designed to be used with the internals of the Hubsan X4 drone. It has been tested many times and does fly. ...This design almost seems indestructible in comparison to other 3D printed designs.
thingiverse
(last pic shows wonky measurements of his design) So instead of trying to redraw it correctly, i decided to make my own frame. My design is "roughly" the same measurements but the circuit holder is placed more forward. I haven't been able to try...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=805325 Instructions Using the following options: Motor_Cap_Wall_Thickness = 2 Length = 65 Which_Parts = frame FC_Width = 25 Resolution = 100 Motor_Hole_Scaling = 1.0 Motor_Diameter = 7...
thingiverse
Hubsan X4 FPV Racer Frame 110 with LEDs for CL-0820 Brushed Motors Lipos 1s 350mah-600mah 1x Hubsan H107C X4 (electronic) 4x M3 Nylon screws 1x FPV camera FX797T 3-In-1 Super Mini 5.8G 40ch AV Video Transmitter Print Settings Printer: Mendel90/NEO...
thingiverse
A battery holder clip for the Hubsan X4 frame by kcedge (http://www.thingiverse.com/thing:229994). Use a piece of foam between the control board and the battery to protect the battery from the board and to hold it in place against the clip. ... Easier...
prusaprinters
here is v1 . (please post pictures of makes i would like to see my drones around the world..) I decided to try something different with my hubsan x4 frames .. got tired of typical h frames and so on.. so I designed this v1 of more to come new style...
thingiverse
(please post pictures of makes i would like to see my drones around the world..) I decided to try something different with my hubsan x4 frames .. got tired of typical h frames and so on.. so I designed this v1 of more to come new style hubsan x4...
pinshape
(please post pictures of makes i would like to see my drones around the world..) I decided to try something different with my hubsan x4 frames .. got tired of typical h frames and so on.. so I designed this v1 of more to come new style hubsan x4...
thingiverse
this is a replacement for the original x4 frame. it uses the standard 7mm motors (attention: 8.4mm motors on the h107c). the receiver can be screwed into the frame. I'd recommend to use electrical tape or a rubber band to attach the battery. the...
thingiverse
a little experiment on my hubsan x4, waiting for the fpv cam to mount on it Print Settings Resolution: 0,2 mm Infill: 10% or 0% Notes: The bottom cap has to be printed with supports then carefully clean the excess plastic until ir fits snug on the...
thingiverse
this is very similar to my smaller 57mmm frame: http://www.thingiverse.com/thing:435484 the distance between the motors is 87mm, which is the biggest possible span for the stock motor wires. the flight behaviour is really different, i'd describe it...
thingiverse
light frame for hubsan x4 electronics 7mm motors
thingiverse
Step 13: Debrief activity with students and brainstorm for next steps in possibly upgrading their project to do other things (ie: better camera, propellers, etc.) Materials Needed Tools Required: 1.Soldering Iron 2.Wire Cutter 3.Wire Stripper 4.Screw...
thingiverse
This is my micro quadcopter V1 frame design. ... You can fly this quadcopter with Hubsan X4 electronics (8.5mm motors). I have also build a V2 frame design. ...Checkout my other Things!
thingiverse
This is my micro quadcopter V2 frame design. ... You can fly this quadcopter with Hubsan X4 electronics (8.5mm motors). I have also build a V1 frame design. ...Checkout my other Things!