hubsan x4 h107l upgrades 3d models
34889 3d models found related to hubsan x4 h107l upgrades.thingiverse
Lightweight bumper for the Hubsan X4 H107L * flight tested! ... * as lightweight as I dare * works with PLA, no problem * print without supports
thingiverse
Protection d'hélice pour drone hubsan h107L, moteur 7mm J'ai optimisé au maximum le poids, proche de 4g Imprimé en ABS
thingiverse
This is my first octocopter prototype, a modification of the famous Hubsan X4 H107L quadcopter. The original Hubsan 240mAh battery lasts not very long. Adding a second one parallel to the first one will probably extend flight times. With a 1000mAh...
thingiverse
Have a ready to fly unit made for you or contact us if you need just the 3D printed parts: https://www.etsy.com/shop/cuddleburrito Alternate body for Hubsan X4 quadcopter H107L, but 8.5mm motor mounts included too. Maiden...
thingiverse
Infill: 100% Layer Height: 0.2mm Bottom Piece: 4 Perimeters Top Piece: 4 Perimeters
thingiverse
I didn't receive the prop guard for the X4 and after 5 min of trying to fly or more accurate, 5 min of crashing, I realised I needed it bad. I tried some of the versions found her at thingiverse but non fitted that well. I think they are made for...
cults3d
Just lost my Husban H107C in my garden...and bought a new H107L :) So here is the remix of the Hubsan guard for H107L model (7mm motor instead of 8mm) - I also reinforced it where it used to break when crashing...
thingiverse
Just lost my Husban H107C in my garden...and bought a new H107L :) So here is the remix of the Hubsan guard for H107L model (7mm motor instead of 8mm) - I also reinforced it where it used to break when crashing...
thingiverse
juste une autre protection d’hélice pour Multicopter h107L. ...j'ai refait un model car ceux que j'ai trouvés sur le site s'adaptaient mal sur le drone.
thingiverse
boite de transport pour mini drone hubsan H107L avec des emplacements pour le chargeur USB, 2 batteries, 4 hélices
thingiverse
Specs: Motor Hole Diameter: 8mm(See Update) Internals: H107L Part Count: 2 UPDATE 1: I modified the motor holes to 8.5mm so that the Hubsan H107C motors will fit. I also lowered the motor holes so the motors will stick out the top more. For this,...
thingiverse
This is a 6.5 gram frame specially designed for hubsan x4 h107L but it would work just as well for any other micro quad with 7mm or 8.5mm motors. This frame was built to be sturdy yet lightweight (less than half the original frame's weight). This...
thingiverse
An all-inclusive schematic of the Hubsan X4 flight control board.
thingiverse
A simply and light frame it can be used with hubsan x4 electronic (7mm motors).
thingiverse
This is a protection case for your Hubsan X4 with a magnetic cover to keep the drone safe while stored or transported. There is the place to add up to 6 LiPo batteries and spare parts like propellers, USB card or propeller tool. Originally...
thingiverse
I'm not sure how you would do the electronics but here is a hubsan x4 octocopter.
thingiverse
My individual Cage for a Hubsan X4 Drone. ... Instructions I mesured the drone the build a cage.
thingiverse
Amateur edit of frog box to make it slightly bigger to hold a Hubsan X4 and all its accessories. Note: Uses almost an entire spool of filament! ...
thingiverse
Feet for Hubsan X4 Quadcopter. ...4 different models Just print 4 of the same model, and clip them :) No support needed.
thingiverse
A wall mount designed to hold the Hubsan X4 H107C. ...Print Settings Printer Brand: Printrbot Printer: Simple Black ...
pinshape
SummaryFeet for Hubsan X4 Quadcopter. ...4 different models Just print 4 of the same model, and clip them :) No support needed.
thingiverse
Replacement frame for my hubsan x4 that I broke. ...It ended up being about 25% lighter than the original one, and feels sturdier.
thingiverse
Clamp on fan ducts for hubsan x4, shown on alpinedrones' frame http://www.thingiverse.com/thing:717375 Print Settings Printer: FlashForge Dreamer Rafts: Doesn't Matter Supports: No Infill: 100%