hubsan x4 propeller size 3d models
498439 3d models found related to hubsan x4 propeller size.thingiverse
A propeller guard for a Hubsan X4 107C+. Note that it will probably only fit this very specific model! There are many drones under the name of Hubsan X4 and they don't look the same. In hindsight it could probably have been made a few grams lighter...
thingiverse
Printed for my quadcopter Hubsan X4 H107C (last photo) Instructions Hard model, impossible to print without support at FDM tech. I've printed this on Russian 3D-printer Picaso 3D Designer at 0.1 mm layer resolution using autogenerated support from...
thingiverse
... in TPU... it's very floppy, but hopefully will keep the propellers from breaking on impact. If not, I'll print thick variety in ABS and try it out. Hopefully it won't be too heavy. Let me know of any suggestions or feedback! ... Thanks!
thingiverse
a little experiment on my hubsan x4, waiting for the fpv cam to mount on it Print Settings Resolution: 0,2 mm Infill: 10% or 0% Notes: The bottom cap has to be printed with supports then carefully clean the excess plastic until ir fits snug on the...
thingiverse
Within this thing you can safely store your Hubsan X4 with spare parts, usb-card, propeller tool and batteries. The original box was intended for the Hubsan-X4 - H107C On request I added a box for the Hubsan-X4 - 107D (only the 4 little circles...
thingiverse
A simply and light frame it can be used with hubsan x4 electronic (7mm motors).
thingiverse
An all-inclusive schematic of the Hubsan X4 flight control board.
thingiverse
My individual Cage for a Hubsan X4 Drone. ... Instructions I mesured the drone the build a cage.
thingiverse
I'm not sure how you would do the electronics but here is a hubsan x4 octocopter.
thingiverse
Within this thing you can safely store your Hubsan X4 H107P with spare parts, battery charger, propeller tool, 4 batteries 3.7V 520mAh LiPo and 4 AAA batteries. UPDATE: 01/06/2016 New design - Box and Plate Still to do - Cover Print Settings Printer:...
thingiverse
Feet for Hubsan X4 Quadcopter. ...4 different models Just print 4 of the same model, and clip them :) No support needed.
thingiverse
A wall mount designed to hold the Hubsan X4 H107C. ...Print Settings Printer Brand: Printrbot Printer: Simple Black ...
thingiverse
Lightweight bumper for the Hubsan X4 H107L * flight tested! ... * as lightweight as I dare * works with PLA, no problem * print without supports
thingiverse
Replacement frame for my hubsan x4 that I broke. ...It ended up being about 25% lighter than the original one, and feels sturdier.
pinshape
SummaryFeet for Hubsan X4 Quadcopter. ...4 different models Just print 4 of the same model, and clip them :) No support needed.
thingiverse
Amateur edit of frog box to make it slightly bigger to hold a Hubsan X4 and all its accessories. Note: Uses almost an entire spool of filament! ...
thingiverse
1x Main hubsan Motherboard all that you need is connect to each motor pad 2 same motors with same propelers. ... Video v1http://youtu.be/Gz8qETTCyA8 Video V1 8mm versionhttp://youtu.be/oaxj_nEeL7g Thanks to http://www.thingiverse.com/thing:232527 for...
thingiverse
This is a protection case for your Hubsan X4 with a magnetic cover to keep the drone safe while stored or transported. There is the place to add up to 6 LiPo batteries and spare parts like propellers, USB card or propeller tool. Originally...
thingiverse
Clamp on fan ducts for hubsan x4, shown on alpinedrones' frame http://www.thingiverse.com/thing:717375 Print Settings Printer: FlashForge Dreamer Rafts: Doesn't Matter Supports: No Infill: 100%
thingiverse
*** Hubsan X4 H107, Race drone body by Jhedstrom *** Remixed to 8.5 mm. When adding motors pass cables through and under rather than using the slot as this often cuts the cables if inserted with not enough slack. ... Works extremely well with 8.5mm...
thingiverse
A lightweight prop guard for the Hubsan X4. I don't have the best scale, but it weighs somewhere less than 3 grams. Edit: Added a thicker version. Print Settings Printer Brand: LulzBot ...