hue remote 3d models
18879 3d models found related to hue remote.thingiverse
used to hold the Phillps hue remote, https://www.philips-hue.com/en-us/explore-hue/how-it-works/wireless
thingiverse
It is for my Philips Hue Remote project located on my blog at [mylifeasa.tinkerer.us](https://mylifeasa.tinkerer.us/philips-hue-remote-using-esp8266-6afaf76ac8a8), but could be used for other projects with the same hardware requirements. Files...
thingiverse
A simple cover, in case you like me would like mount a hue remote on a non-white wall and make it less visible. It hides all except the remote part. Easily remove-able. Possible to mount on existing wall mounted remotes. Tight fit, will probably not...
thingiverse
As I wanted to have a nice little stand on my table for the hue remote, I made one! ... For that I used the already existent remote holder (as that looked nice and has the shape figured out) and added the standing part to it.
thingiverse
# Philips hue Remote Mount This is a phlips hue zigbee remote mount. In the back of the mount there are 2 circles for putting in a magnet (10mm diagonaal, 2mm hight). ...I left some space for hotglue for the magnets.
prusaprinters
We wanted a small holder for it to mount on the wall next to the physical light switch, so I made this lightweight mount.It has a space to superglue a 20x1 (or 20x2 if you really press it) neodynium magnet to keep the remote in place.There's now also...
thingiverse
Simple cover (plate) for Philips Hue remote dimmer. I use double-sided tape to fix the cover over the original switch. --- Simple support pour interrupteur Philips Hue. ...J'utilise du ruban adhésif double face pour fixer le couvercle par dessus...
thingiverse
It also uses the magnets that came with the original Phillips Hue remote plate, they were still tacky enough when I pried them off the old plate that they stuck to the new plate long enough for me to snap the cover on top which secures them. ...
prusaprinters
I was inspired by Jutrasb's printable plate (link below), but I needed one that was a little bigger since I didn't want to repaint the wall, and also I didn't want the screw holes showing. Since I've been learning Fusion 360, I decided to work on it...
thingiverse
The LivingColours and LivingWhites remotes work with the Hue ecosystem making them a formidable light switch+dimmer. This holder is for a bed back panel but would work on any board. ...The SCAD source is supersimple so should be straightforward to...
thingiverse
This is a cover for philips hue dimmer switches. The cover has enough space in the back for it to be placed on top of an existing toggle switch without having to remove the toggle or mess with wiring. ... 0.5mm recessed channels are on the back of the...
thingiverse
The insert has two cavities to insert the magnets from the original Hue wall mount during the print. I hope that with uploading my designs I provide you with a helpful tool or even just a fun thingamabob. Of course designing takes time. So if you...
prusaprinters
Models designed to easily mount the Hue LightStrip and the Hue Remote into your existing setup. The Hue Remote mount fits the Gira 55 Standard or the Gira 55 E2 (square design). A magnet with a diameter of 20mm and height 2mm can be press fit in the...
thingiverse
I was tired of having my Philips hue remote be on a separate holder from my light switches. I modeled this one to be a single, cohesive unit. ...Fits over my existing switches and screws.
thingiverse
If you print, or just like, this thing then please consider: There are other Hue remote to dual gang box mounts on Thingiverse, but what if you have a single gang box with a light switch or USB outlet (or as I pictured a fireplace control) and need...
thingiverse
Philips Hue remote control rod mount. The remote control can be slid in and out easily but still with a tight fit. Print the mount with PETG because this flexes better than PLA and does not break when bending. A 16mm M3 screw and a hexnut are...
thingiverse
Super clean removable mount for Philips Hue dimmer remote! Easy to print (not much support required) and easy to sand visible surfaces to increase aesthetic appeal! ... Can replace an existing switch (appropriate wiring modifications necessary -- BE...
thingiverse
This is a simple decora switch blank to hold a Philips Hue remote. I saw several different versions, but this one was specifically made to re-use the magnets from the holder that came with the remote. Also, I didn't want any kind of "mount" to show...
thingiverse
Which is how it's setup in my example pictures - the two real switches are in a box in the wall, and the Hue remote is attached to the cover plate on top of solid wall. It works great!! The remote is slightly south of center when it hangs on the...
thingiverse
Simple wall-mount holder fpr the Philips LivingColor remote, round version. Print and enjoy! The HueHolder.stl comes with 2 holes for screws, the HueHolderNoHoles has (surprise!) no holes and can be used to glue it to the wall or whatever place you...
thingiverse
A remote holder for the Philips Hue remote. ...Nice and simple, and still allows full use of all the buttons and can easily slide in and out.
thingiverse
Unfortunately our existing rocker switches protrude further (5mm) and prevent the Hue remote from lying flush. This together with a couple of other niggles led me to go back to basics, draw a fresh angular outline in SketchUp, copy the dimensions and...
thingiverse
The original light switch is still accessible when the Hue remote is removed. I did this as a quick modification of my double-hue switch cover, when my triple light switch turned out to be a bit too wide and deep for the otherwise excellent switch...
thingiverse
Wall-mounted holder for the Philips LivingColor remotes. New for this version: It fits the older generation 2 remotes. I also modified the design to have wider walls to improve the print bed adhesion. It is based on the great design of jwildeboer...
prusaprinters
Wall-mounted holder for the Philips LivingColor remotes.New for this version: It fits the older generation 2 remotes. ...I also modified the design to have wider walls to improve the print bed adhesion.It is based on the great design of jwildeboer...
thingiverse
... model. There is a space for a 20mm disc magnet to hold the remote in place. f3d file included so that the height can be changed if required. ... The included stl is suitable for a switch with a maximum height of 15mm to the top of the rocker.
thingiverse
Simple cover that can be used to mount the hue remote base directly infront of a lightswitch with 10 cm diameter. ... Only suitable if there is a noticable gap between the frame of the light switch and the wall.
thingiverse
Use this if you wish to replace your the light switch for your Philips Hue bulbs with a Philips Hue remote, hard-wiring the old switch to permanently-powered and relying solely on the remote and Hue bridge to control your bulbs. The plate is...
prusaprinters
This is based on Two-Gang Light Switch Plate for Philips Hue Remoteby viettamluu June 06, 2018https://www.thingiverse.com/thing:2948880However... this version mounts over a single gang wall box, instead of a two-gang wall box.</p><p>Designed to fit...