huina 1550 3d models
486 3d models found related to huina 1550.thingiverse
** Ripper for the Huina 1550 / 550 Excavator ** * Needs (3x) M2x8 screws for the pads * OR use it without pads for easier ripping in hard ground V2 corrects a clearance issue with my Spring Coupler (https://www.thingiverse.com/thing:3732951)
thingiverse
This is a replacement muffler for the Huina 1550 for those that lost it or if your cat chewed it ;) Should bolt right up to the stock battery cover with the stock screw.
prusaprinters
Ripper for the Huina 1550 / 550 Excavator Needs (3x) M2x8 screws for the pads OR use it without pads for easier ripping in hard ground V2 corrects a clearance issue with my Spring Coupler (https://www.thingiverse.com/thing:3732951) Print...
thingiverse
** Cabin Bars / Grill / Protector for Huina 1550 ** * Either print in 8 parts (print_7 and print_1) or the complete thing. * Glue together the 8 parts then double-side sticky tape the grill to the cabin. * V2 fixes a tolerance issue around the...
prusaprinters
Cabin Bars / Grill / Protector for Huina 1550 Either print in 8 parts (print_7 and print_1) or the complete thing. Glue together the 8 parts then double-side sticky tape the grill to the cabin. V2 fixes a tolerance issue around the bottom window...
thingiverse
Upper Shell made for the Huina 1550 as a Conversion to a Liebherr R942 Model Excavator. Its still a WIP, so be careful. The Door on the Right side is made for a hinge, so to change the stick accu pack inside. ... There are also 2mm holes on the...
thingiverse
By request, here is the Huina 1550 rear drive sprocket. Direct copy for those that broke one or just need a spare for STOCK gearbox. ... PS.: I haven't printed this so i need your feedback, please comment if it worked or not and why :D Update:...
thingiverse
** Huina 1550 Progressive Link Thumb ** * Your choice of : * * Short : Use without a quick coupler or for a shorter thumb * * Long : Use with the quick coupler * Not compatible with stock square drive * Not compatible with stock remote * Not...
thingiverse
** Huina 1550 excavator "5 finger" rake. ** * REQUIRES my quick coupler OR the screw-cylinder mod. There is no square hole in this to drive it from the stock bucket motor ! * Requires (1x) M4x45 bolt and nut to make the front attachment pins.
prusaprinters
Huina 1550 Progressive Link Thumb Your choice of : Short : Use without a quick coupler or for a shorter thumb Long : Use with the quick coupler Not compatible with stock square drive Not compatible with stock remote Not compatible with 580...
prusaprinters
Huina 1550 excavator "5 finger" rake. REQUIRES my quick coupler OR the screw-cylinder mod. There is no square hole in this to drive it from the stock bucket motor ! Requires (1x) M4x45 bolt and nut to make the front attachment pins. The rear one...
thingiverse
This is a replacement gear for the arm gearboxes. ...This gear replaces the output gear of each gearbox which failed on my Huina 1550. ... Enjoy it, and if you like my design, feel free to offer me a tip: www.paypal.com/paypalme/michaelrose1981
thingiverse
** Here is my first concept of a "quick coupler" for my new Huina 1550 :D ** *** This is for a stock Huina without mods ! *** For the moment, it is a manual coupler, meaning you have to remove 1 bolt to detach the bucket. You can make yourself a...
thingiverse
** Bucket push rods for your Huina 1550 ** *** This allows more angle of the bucket if used in addition to my other mod here : https://www.thingiverse.com/thing:3723652 *** Print one of each part except (2x) horizontal_v1 The cylinder_spacer is made...
prusaprinters
Here is my first concept of a "quick coupler" for my new Huina 1550 :D This is for a stock Huina without mods ! For the moment, it is a manual coupler, meaning you have to remove 1 bolt to detach the bucket. You can make yourself a 3mm pin with a...
prusaprinters
Bucket push rods for your Huina 1550 This allows more angle of the bucket if used in addition to my other mod here : https://www.thingiverse.com/thing:3723652 Print one of each part except (2x) horizontal_v1 The cylinder_spacer is made to go in the...
thingiverse
** Huina 550 / 1550 Undercarriage ** * Spring tensioner * Bearing rollers * More ground clearance under the center section (about 30mm instead of 8mm stock) * Fits stock Huina track gearboxes (a little plastic snipping required only) * Fits stock...
prusaprinters
Huina 550 / 1550 Undercarriage Spring tensioner Bearing rollers More ground clearance under the center section (about 30mm instead of 8mm stock) Fits stock Huina track gearboxes (a little plastic snipping required only) Fits stock Huina front idler...
thingiverse
I made these last summer but forgot to upload them. They are made to go over the upgraded screw-cylinders that you buy online. ... Use a dab of glue if they're too loose for you (depends on your printer nozzle)
prusaprinters
Spring-loaded coupler compatible with the Huina 550 / 1550 or 580 V5 has more clearance added for the bucket, lock and bolts parts. Shouldn't need much filing/sanding. Also added a bevel to make hooking a bucket easier. If V4 worked fine for you,...
thingiverse
** Spring-loaded coupler compatible with the Huina 550 / 1550 or 580 V1-V2-V3** ** Does NOT fit 580 V4 bucket, I will try to remix it if I can get dimensions ** ********** ** For the 580, use the "580_Spring_Coupler_xxx.stl" files ! ** ********** ...
thingiverse
Umrüstsatz für den Bagger von Schaufel auf Greifer. Um die 4-kant-Stange sauber durch den gedruckten Greifer zu bekommen am besten mit einem Feuerzeug erhitzen und mit einem kleinen Hammer vorsichtig durch das Druckteil klopfen. Man könnte das...
prusaprinters
Huina Excavator Electric Coupler * Use the 580_ labeled files for the 580 / 1580 v1 v2 v3 v4 UPDATE Someone made a printable lead screw version for use with "D-shaft" N20 motors. "Electric_LEAD_Lock.stl" "LEAD_Screw.stl" ! Thanks to m. ...Liski for...
thingiverse
** Huina Excavator Electric Coupler ** *** Use the 580_ labeled files for the 580 / 1580 v1 v2 v3 v4** ** UPDATE ** Someone made a printable lead screw version for use with "D-shaft" N20 motors. * "Electric_LEAD_Lock.stl" * "LEAD_Screw.stl" ! Liski...
thingiverse
To increase the power of the arm of your RC excavator, you can strengthen the springs of each arm gearbox. This is a common mod with the risk of breaking the gearbox. With this clip, you keep a rest functionality of the original slipper clutch. ...
thingiverse
production process https://www.youtube.com/watch?v=DsxnJYMFS5Y Necessary parts -3mm steel rod 29mm -3mm steel rod 22mm -spring with moderate elasticity -M3 bolt nut 40mm 2ea PLA Adhesion using acrylic bond
thingiverse
... 2019 ! Comments / Suggestions welcome. ** I got lots of people adding this to their "Warhammer 40k" collections. Not sure why, but this is NOT related to Warhammer. This is a part for a remote controlled toy excavator sold as the "Huina 1550" **
prusaprinters
... I got lots of people adding this to their "Warhammer 40k" collections. ...Not sure why, but this is NOT related to Warhammer. This is a part for a remote controlled toy excavator sold as the "Huina 1550" Print instructionsCategory: R/C Vehicles
thingiverse
** This is Erdinger's bucket remixed for the Huina Excavator (1550 / 550 / 580) ** Weights less than the metal bucket which is a nice bonus. Is plenty strong even for the servo-screw modified rigs. * Sand Bucket now available (larger, no teeth) ...