hunter pgp tool 3d models
110195 3d models found related to hunter pgp tool.thingiverse
This is a tool I created after I had to replace and adjust a bunch of Hunter PGP rotors. You can use their little white plastic key to hold the head up while you adjust or do it with the water running. This allows you, without turning the...
prusaprinters
... werden.</p><p>Wird bestimmt auch bei anderen Modellen passen. Kann ohne Support gedruckt werden.NEU! HUNTER PGP -04 ULTRA Versenkregner/Getrieberegner, 10 cm, 50° bis 360°, 3/4" IG - NACHFOLGERMODELL DES HUNTER PGP-ADJ : Amazon.de: Garten
thingiverse
This is a simple cover for Hunter PGP Ultra sprinklers to keep grass and dirt away from the screw on top. This makes it much easier to remove the sprinkler at the end of the season (if needed in your area). ...The 3 holes can be used to fix the cover...
thingiverse
Hunter tool for adjusting rotary sprinkler heads. Hex key should be used with caution. ...3/32" key maybe a better option because of size and limited strength.
thingiverse
This is a custom pump handle for a Sheridan PGP paintball pistol. Print vertically with no supports. ...It is recommended that it be printed solid.
thingiverse
This is a PGP project I have been working on for a few year. Actually I started it. Put it down. Then recently picked it up and finished it. So I wanted a cool tip on the barrel, so I made one. ...Fits great.
thingiverse
This is an extended feed plug for the Sheridan PG and PGP paintball markers. This design uses the original Allen screw from the stock feed plug and two #015 o-rings to secure the plug in place. There is also a hole running through the plug with a...
thingiverse
Tool for removing hunter Sprinkler Heads from the ground. Fits right on top and turn with a wrench to remove. ...Seen a tool for $70 that does this and that's ridiculous
thingiverse
This is the second version of my PGP pump handle. It was designed for the Initeq #10-32 long brass inserts. Previous prints with less than 100% infill cracked when bending the pump arm into place for the PGP2's quick strip bolt. This version was...
myminifactory
This is the second version of my PGP pump handle. It was designed for the Initeq #10-32 long brass inserts. Previous prints with less than 100% infill cracked when bending the pump arm into place for the PGP2's quick strip bolt. This version was...
cults3d
Here is a character inspired by Uvoguine and Nobunaga from the manga Hunter X. Hunter. ... File featuring the character in full and with a cutout.
cults3d
Hit Points Hit Dice: 1d10 per Hunter level Hit Points at 1st Level: 10 + Constitution modifier Hit Points at Higher Levels: 1d10 (or 6) + Constitution modifier per Hunter level after 1st Proficiencies Armor: Light and Medium Weapons: Simple and...
thingiverse
Hit Points Hit Dice: 1d10 per Hunter level Hit Points at 1st Level: 10 + Constitution modifier Hit Points at Higher Levels: 1d10 (or 6) + Constitution modifier per Hunter level after 1st Proficiencies Armor: Light and Medium Weapons: Simple and...
thingiverse
Customized version of http://www.thingiverse.com/thing:340321 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=340321 Instructions Using the following options: BlockLength = 10 Name = Hunter Smith BlockWidth = 5
sketchfab
The hunter figure is said to symbolize the origin of the city name, which comes from the word Strzelec (hunter). The fountain with the bronze memorial was designed by Peter Lipp in 1929 on behalf of the Magistrate of Groß Strehlitz and built by the...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: stick_thickness = 3 hole_radius = 3.5 Font = write/orbitron.dxf font_thickness = 5 stick_width = 10 flat_bottom = 1 message = Hunter font_size =...
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: flat_bottom = 1 message = hunter font_thickness = 5 hole_radius = 3 stick_thickness = 3 stick_width = 8 Font = write/orbitron.dxf font_size = 10
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=175150 Instructions Using the following options: font = write/orbitron.dxf fontsize = 8 corner_radius = 3 text_style = -80 line_10 = slitwidth = 4 slitlength = 12 line_9 = line_8 = line_7 =...
thingiverse
Update 01Apr2017: I have cut the hunter into pieces so that he can be reposed. I am using TinkerCAD for the posing because it makes combining all the pieces via boolean a lot easier. The pieces are not made to be printed separately (yet) so you...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: borderextruder = extruder4 lug_length = 4 font_style = bold font_weight = 0 font_outline_style = rounded bar_thickness = 2.4 inner_margin_width =...