husky wrench organizer 3d models
73730 3d models found related to husky wrench organizer.thingiverse
These are nesting cups for the [Husky 10-compartment interlocking small parts organizer](https://www.homedepot.com/p/Husky-10-Compartment-Interlocking-Small-Parts-Organizer-in-Black-235587/302939645) bins. I'm not sure if the bins are the same size...
thingiverse
Assortment of modified cups for the [Husky 10-Compartment Small Parts Organizer](https://www.homedepot.com/p/Husky-10-Compartment-Interlocking-Small-Parts-Organizer-in-Black-235587/302939645). Magnets used in this project were 0.095" x 0.1"...
thingiverse
These are dividers for the bins in the Husky organizer trays. There are 'horizontal' versions to split the bin into two parts horizontally, and a 'horizontal and vertical' versions to make four compartments. ... I made them just a little bit wide so...
thingiverse
**Husky Parts Organizer** https://www.homedepot.com/p/Husky-10-Compartment-Interlocking-Small-Parts-Organizer-in-Black-235587/302939645 **OnShape Models**...
prusaprinters
The added benefit is that I can take out each cup that I need and put the rest away. Print instructionsCategory: Organization Summary 6 different size cups for the Husky 11in organizer. I have made half sized cups that can be stacked on top of each...
prusaprinters
Make what you want. Husky Parts Organizer https://www.homedepot.com/p/Husky-10-Compartment-Interlocking-Small-Parts-Organizer-in-Black-235587/302939645 OnShape Models...
thingiverse
Inspired by TheSameNameTwice's organizer cups for the 11in Parts Organizer ([link](https://www.thingiverse.com/thing:4378152)), I made a set a little bigger for the 12in container. I bought a Husky 12in Small Parts Container, but wanted to store all...
thingiverse
6 different size cups for the Husky 11in organizer. I have made half sized cups that can be stacked on top of each other as well as full sized. I make these because I have small hardware parts in quantities that wouldn't fill up an entire section.
thingiverse
These are trays that can fit into the bins that come in the Husky Organizers from home depot. This way you can fit up to 4 different parts in a single bin but still keep them separated. ...
thingiverse
... wrench sets. ...We use a couple small magnets next to the horizontal bars to keep them in place in our tool chest. Original file holds 6 wrenches; extended file holds 7. The organizer is 22.25mm tall (without wrenches). ... Design by Erin Cole.
thingiverse
Thanks to the wrench organizer you can group your tools and never lose it again. Specially designed for 6 metric wrenches: 6/7, 8/9, 10/11, 12/13, 14/15, 16/17. Print Settings Rafts: No Supports: No Infill: 10% Notes: I printed the organizer with...
thingiverse
This time for my Craftsman midget wrench sets I can't stand how much space commercial tool organizers waste so these only have 1mm of space between them. Included are 10 PC. Metric: 4, 4.5, 5, 5.5, 6, 7, 8, 9, 10, 11 10 PC. ...Fractional: 5/32",...
prusaprinters
Wrench organizer ment to be used in a rolling toolbox, with hole for magnet underneath. I made this to keep my various wrences from getting lost in the drawer. ...There are 2 different depths of the modules, which each have 3 spaces. </p><p>Hole...
thingiverse
Other Wrench organizer for Parkside set. With the use it was broken. Maybe because the gapes between wrench are tight or for low infill, so I decided to make it with aluminum (some "U" aluminum profile and angle grinder tool...), but here I upload...
thingiverse
No More hap-hazard wrenches loose in drawer. ... wrenches snap right in and the size of the wrench is visible.
prusaprinters
We use a couple small magnets next to the horizontal bars to keep them in place in our tool chest. Original file holds 6 wrenches; extended file holds 7. The organizer is 22.25mm tall (without wrenches). Design by Erin Cole. Print Settings Printer...
thingiverse
I was looking for tool organizers on thingiverse , but I could not find the corresponding size for my wrenches .. so i created a smaller version .. feel free to adjust .. ... i printed the organizers with PETG filament ..
thingiverse
A wall mount for eight wrenches. I printed it in PLA with 15% infill, 2 shells and 0.25mm layer height with a 0.4mm nozzle. Sturdy enough. ...
prusaprinters
A wall mount for eight wrenches.I printed it in PLA with 15% infill, 2 shells and 0.25mm layer height with a 0.4mm nozzle. ...Sturdy enough.</p>
prusaprinters
This is a wrench holder for inside a toolbox or tool trolley. ...It can hold wrenches from (metric) size 5.5 up to 24.
thingiverse
Remixed a Husky Parts Organizer Cup from benjamenjohnson to fit in the Husky Connect system where the bins are a little longer but very similarly shaped. This sits inside of the Husky Connect Small Parts Organizer bins and splits it into 3...
thingiverse
... smaller items in the bins. 3 Styles: 1 Bin 2 Bins 4 Bins Link to the container: http://www.homedepot.com/p/Husky-14-in-15-Compartment-Bin-Small-Parts-Organizer-83053N13/204536846?MERCH=REC-_-rv_search_plp_rr-_-NA-_-204536846-_-N Model# 83053N13
prusaprinters
I bought a set of picks and decided to print an organizer to hold them. 2 #8 screw holes for wall mounting. ...0.8mm nozzle with 0.4mm layers.</p>
thingiverse
Just a spacer for this modular wrench organizer https://www.thingiverse.com/thing:4776998