hydration bladder dryer 3d models

A base and adapter to use a 75mm x 30mm blower fan to speed up drying hydration bladders. ... I used this fan: https://www.amazon.com/gp/product/B07RP14KML/

Add a 5v blower, a power source, and a few screws to this gadget, and you'll have a way to quickly dry out the bladder from a hydration pack (like a CamelBak) for storage. If you've ever left water in one, even a little bit, for more than a week or...

<p><br>I used this fan: https://www.amazon.com/gp/product/B07RP14KML/</p>

For that, I created this dryer that can be slid into the hydration bladder to prop it open, with a stand to let the remaining water run out and a hanger to then let it dry up completely, at some place where it doesn't get in the way. The dryer...

Designed an adapter to fit an 80mm USB powered fan to dry hydration bladders. Two adapters, one for Outdoor Products Last Drop system, and one for Camelbak PureFlow. Although both adapters are about the same size, the thread forms are very different...

proto-type drying rack for hydration bladders

Create a better Hydration bladder holder for my bag pack. ... Screws are 2x M4 12mm with Nuts in Place on the other side.

Create a better Hydration bladder holder for my bag pack. ... Screws are 2x M4 12mm with Nuts in Place on the other side.

This is a protection cap for Evoc Hyrdation Bladders, because they are not delivered with one. So I designed my own with FreeCAD :) It fits perfect for me! The "steg" is for holding the cap on the hose and you can fix both with some cable ties.

I previously used a large spoon to aid drying out my Camelbak bladder, but it wasn't that good of a solution. ...This design isn't anything fancy, but it does a great job of holding the walls of the badder apart to dry it out.</p><p>I printed it in PETG...

A base and top to blow air into a hydration bladder to speed up drying. Used with a 12V 75mm x 30mm brushless blower fan. ... I used ASIN: B07RP14KML https://www.amazon.com/Wathai-Brushless-Cooling-Turbo-Blower/dp/B07RP14KML

This mount is the perfect way to hang your hydration bladder to dry. ...I was tired of hanging mine on open cupboard doors so I realized I could use my Skadis pegboards.</p><p>The base plate uses my <a...

This is a magnetic clip for Hydration Bladders with tubes from 9-10mm in diameter and for pack webbing of 20mm. I found other designs but found them bulky and not as secure. I designed this one so the magnets on the clip protrude slightly and are...

This is a magnetic clip for Hydration Bladders with tubes from 9-10mm in diameter and for pack webbing of 20mm. I found other designs but found them bulky and not as secure. I designed this one so the magnets on the clip protrude slightly and are...

Hi, after the connector for my USWE hydration bladder broke and I couldn't find a replacement part I designed this. It fits perfectly for my hydration bladder. Please use a O-ring seal on the thin notch. Before using it please inform yourself...

This is a collection of inserts that are useful to insert into hydration bladders for the purpose of propping the sides apart so they dry faster and more thoroughly. I'm currently in training for an ultra marathon so I'm using bladders more often...

This is a Platypus water bladder dryer. I got the idea from the other one that is posted but I wanted to do my own and added a ridge to keep in inside the bladder. I also designed it so that it doesnt need to have any supports and it has an inlet...

This is a drying hook and spreader for a Camelbak Crux hydration bladder. It should fit most bladders - Camelbak and other brands - that have a removable hose The hook captures the bite valve of the hose and the bladder connector to hang them for...

The formation of bad odors is reduced and can thus extend the life of the bladder. The ellipse was designed for the use with a 2 liter water bladder manufactured by Source. The model was developed as a proof of concept. ...For regular use, I advise the...

This is a dust & dirt protector cap for a hydration bladder. The cap has an internal diameter of 19mm which fits the Mountain Warehouse Wide Opening Hydration Pack 2L but can be scaled up and down as required. It attaches with a cable zip tie as...

Protective cap for the hydration pack from b'twin, useful for trekkers who want to keep the tip clean.

The included values are okay for my Deuter Futura backpack and SOURCE hydration pack, but it should be entirely customizable. ... Based on https://www.thingiverse.com/thing:2889126

I made own hydration reservoir dryer. It fits 2L, 3L reservoirs and many other reservoirs with 12cm+ opening. No more mold + cool look in your kitchen! :] Recommended print settings: flexible filaments like Nylon or ABS at least 2.5mm walls for...

I made own hydration reservoir dryer. It fits 2L, 3L reservoirs and many other reservoirs with 12cm+ opening. No more mold + cool look in your kitchen! :] Recommended print settings: - flexible filaments like Nylon or ABS - at least 2.5mm...

I made own hydration reservoir dryer. It fits 2L, 3L reservoirs and many other reservoirs with 12cm+ opening.</p> <p>No more mold + cool look in your kitchen! :]</p> <p>Recommended print settings:</p> <ul> <li>flexible filaments like Nylon or...

Dryer for Source Deuter hydration bladder 3l Version 1 as shown in the photos without step at the dryer´s foot. ... Verision 2 with step at the dryer´s foot for stailized standing and better ventiation.

I designed a hook so you can hang your Camelbak bladder to dry. ... There is also a clamp on the hook to hang your hose.

Customized version of https://www.thingiverse.com/thing:2912390 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2912390

Customized version of https://www.thingiverse.com/thing:2912390 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2912390

Customized version of https://www.thingiverse.com/thing:2912390 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2912390