hypercube evolution configurator 3d models

https://www.facebook.com/groups/Hypercubeevolution/ Decided to try out 10mm hollow X rods. My printer has a 0.2mm nozzle, so fit may vary a little on other printers. This is specifically designed for long "Misumi compact bearings". Regular 10mm...

I built and mostly put together this, as you can see from the pictures. It should work just fine. However, I'm concerned that the center of gravity is a bit too far away from the bearing rods. I'll keep brainstorming ways to solve this problem. One...

Here is the rewritten text: Remix of the 10mm version. ... Check out the 12mm version here.

This design strives to minimize the gap between the Z axis rods to achieve superior stability in bed-tilt direction.\r\n\r\nIt is intended for use with one LM12LUU bearing rather than two LM12UU bearings.\r\n\r\nI opted to utilize a different corner...

It is outdated design, replaced by [HEVO MGN v2](https://www.thingiverse.com/thing:4186819) ================== Because thingiverse doesn't show attached images, you can see full resolution images here https://photos.app.goo.gl/Uec1npeeNbUNK8969. It...

This is my first attempt at combining the best piezo system available with E3D's new Hemera Extruder-Hotend. It's still a work in progress, but for me it's working perfectly so far. Unfortunately, you'll have to print a new X-carriage and lose 21mm...

Check out my new printer - Little Cube - SFF CoreXY Printer https://www.thingiverse.com/thing:4487878 For some unknown reasons, STLs are not previewed, but still available in **Thing Files** section. Update 2020/01/15: I decided to upgrade X & Y...

I remixed an optical flag from a few designs on Thingiverse. I rearranged it so the adjusting screw is at the top instead of the bottom, just like the original designs had it. The length and strength of the screw depend on your specific setup. I'm...

I modified this corner bracket to feature a loop on the back for routing hot end wiring through as well as a spot for my PTFE tube that runs from the machine's corner to the filament sensor on the Titan Aero. This attaches to the upper corner of...

I revamped an LCD case by merging elements from two existing designs. The original case had some specs that didn't meet my standards, so I reimagined it with my own preferences in mind. ... Now you can easily upgrade your LCD setup with a USB 2.0 port,...

Rail Mount System for 20x20 Millimeter Aluminum Extrusions.

Hi, this is still untested... Four Berd Airs are required. It's intended for the self-made version with 3mm aluminum tube (ID 2.4mm), bent with [2869014 ](https://www.thingiverse.com/thing:2869014). All 3mm tube radii are bent using the same tool.

I have redesigned the mounting plate and mount holder for easier printing, allowing the plate to be printed on its backside where it once was attached to the mount. This redesign also makes it simpler to attach other hardware without needing to print...

Remixed and uploaded with style, thanks to the talented designer Javis K!

Human: Enhanced OmniCore Housing Frame Foundation bolstered for added durability and stability.

The original design wisely specifies a pair of LM12UU bearings on each Z-axis rod, which is perfectly acceptable for the single-z-axis version. Nonetheless, if these bearings are not precisely aligned they will stick severely. This revised...

I've remade the design to fit perfectly on an 8mm x-rod. ...The updated model is now included as a Fusion360 file for your convenience.

I designed this system to make swapping out Hotend cartridges quick and effortless, even while my printer is still under construction. To get started, simply build the carriage you need and attach it to Scott's X Carriage. Next, insert one of these...

Adjusting the print bed to clear the heater block from bltouch contact requires precise angle alignment.

Get a clear picture of your print adhesion issues with this no-nonsense full bed calibration. Print at 30mms for impressive results. This setup works well with all beds that can handle prints up to 300mmx300mm in size. New features include a .4...

I adapted the widely-used mount from Vergienc by incorporating an HDMI port, sourced from Delock, directly into the mount itself as well as onto the rear of my printer, which houses the electronics. ...I fabricated this modification using PETG or ABS...

I personally adore the brass accents, I must confess it. ...I've successfully customized NedalLives fantastic pulley mount for 10mm rods to accommodate brass inserts with ease.

I'll be making some adjustments for people but please don't ask me to design mounts for other sensors that aren't compatible with the TronXY XY-08N or the Anet Z Probe. I had rigged my sensor to the side of the original extruder mount, but I wanted...

Here is the rewritten text: I created this from the Hevo Design by SCOTT_3D to transform the FLSUN 3D Cube into a high-performance printer capable of reaching speeds up to 150mm/s. The design includes the Firmware (Marlin 1.1.8) with ABL and without...

I redesigned Chander's Spool Holder to make it more stable for shallow spools that tend to slip off the bearings. Adding a third bearing ensures even smaller spools stay securely in place. ...The pin effectively holds the bearings in position, and I'm...

I built this fantastic electronics enclosure by melnikod, which can be found at https://www.thingiverse.com/thing:2761069. However, I needed to create a mount for my MKS 3.2 TFT display, and that's exactly what I did. This design was completed in no...

I designed this fantastic electronics enclosure by melnikod, check out the original on Thingiverse at https://www.thingiverse.com/thing:2761069. ...However, I noticed that the design was missing a crucial hole for the power cord, so I took matters into...

This is a modified version of lamturbo's flawless EVO XY cable chain, tailored to function seamlessly with warham's enhanced XY carriage system. ...To make it work, I had to trim down the mount that attaches to the X rods, allowing it to fit snugly...

This is a custom remix of the x carriage for the e3d Titan Aero extruder and hot end, featuring added functionality to accommodate the x optical endstop wires, which now feed up beside the extruder motor through a dedicated channel. Additionally, the...

I'm not designed to function without a sensor, which I don't need and adds unnecessary weight. I'm printing on 300mm x 300mm bathroom mirror glass from IKEA or hardware stores like Home Depot or Lowe's. 5/12/18 Added a quick Rev 2 that I've had...