hypercube tech2c 3d models

Filiament Halter für HyperCube Tech2C Drucker. Für Filiament Rolle der Firma alpaplastic.com siehe Bild! Benötigte Teile M8 Schraube 100mm Lang M8 Mutter D9~10 Federn ca. ...10 bis 20mm Lang (optional) F608ZZ Flange Bearing M3x8mm Innensechkant-Schraube...

finalize the tube with Nylon Clamps Suporte para cabos para HyperCube(Tech2C) que utiliza um furo existente no X_Carriage_v1.2. ja possui um rasgo de 4mm para colocar os cabos sem a necessidade de desconectar. depedendo do caso possar ser que seja...

Hallo Jungs und Mädels :) Hab hier einen kleinen Upgrade für HyperCube von Tech2C upgegradet. Fand das alte Halter für ABL Sensor nicht so gut und deshalb zeichnete ich ein Neues :) Gedruckt wurde mit ABS mit 50% Infill und einem Brim, kann auch bei...

addons to z for Z_Carriage_v1.1.stl

Hi Guys, This upgrade has been created for better stability of Heat Bed. There is no play when lowering or raising from the Z axis. ...Regards Gamers RS

Main points were -i wanted it to use a compatible bolt pattern to existing printers like the Tech2C hypercube I have built, which I believe is the same bolt spacing as a prusa i3. ...-to use a radial fan as they are more effective at pushing air under...

Here is my Upgrade for XY Joiner by Tech2C 3D Printer. BOM: 4pcs. drylin® RJMP - 2nd generation of plastic linear bearings 8pcs. M3 x 20mm Socket Cap Bolts 8pcs. M3 x 16mm Socket Cap Bolts 16pcs. M3 Hex Nuts 2pcs. 20T Aluminum Timing Drive Pulley...

For slot in 10mm rod The slot makes is easier to install the rod between the motor and idler

:) This fan duct was designed for "E3Dv6 Bowden X-carriage mount v2 for Prusa i3" by Tech2C (huge shout out to him - he did awesome work!) to support/fit an BLTouch Sensor. There are three versions of the duct with: * small * medium * large ...

:) This fan duct was designed for "E3Dv6 Bowden X-carriage mount v2 for Prusa i3" by Tech2C (huge shout out to him - he did awesome work!) to support/fit an BLTouch Sensor. There are three versions of the duct with: * small * medium * large sized...

Hypercube X Carriage with endstop and magnet compatible with hypercube 300 and hypercube tech2c

a HyperCube (Tech2C) compatible mount for the Dremel 225 flex shaft to use your printer as a cnc

This is a remix of Hypercube by Tech2C Extruder cable support for 200mm tube. ...

This is a remix of Hypercube by Tech2C LCD mount for 12864 smart controller. ... You will need two of them.

This is a slightly larger Z Carriage mount for the Hypercube by tech2C. It helps prevent bed rails from sagging so much. ...

... to capture Nylox nuts for less movement in the bed levelling screws. They are tight to get in and best installed with a long M3 screw. Designed for the original Hypercube by Tech2C, they allow the bed to go all the way down without bottoming out.

Meine Verbesserungen für den HyperCube von TECH2C Für E3D Hotend: Der "Drucker_Halter" ist mit zwei Aussparungen für Kabelbinder sowie mit Befestigungsschrauben für den "Halter_IR-Sensor" . Die "Duese" ist um ca. 2mm kürzer als das Original von...

A hypercube. ...3D printable of course.

i made a hypercube using Rhino3D

Projection of an hypercube on an hypersphere.

Hypercube projected into Three Dimensional space.

i made a hypercube using Rhino3D

This is the standard perspective projection of the Hypercube from 4D to 3D

It's a HyperCube! ...(Well a shadow, but don't ruin my fun :P)

Hypercube is a mathematical representation of a cube in the fourth dimension (Known also as tesseract)

This hypercube can be both an accessory and an ornament for your house. Easy to print and fashionable. ...Enjoy it!

This is an isometric projection of the hypercube in 2 corners and sligthly twisted in 6 corners.

Here is my small Upgrade for HyperCube by Tech2C. Hope you enjoy it :) It was printed with 20% infill and a PETG Magenta Material. ... My Carriage have an Belt Clamp Fix with Socket Cap Bolts and many more Upgrade :) BOM: M3 Hex Nuts "6pcs" M3 Nyloc...

an uncle of mine made this hypercube when i was a kid out of iron wire, i found it very fun to look at, so i designed one to print.

Small hypercube, easy to print with supports. I tried to make a small 1" cube, and it kind of worked (see the 2nd photo), but I wouldn't recommend it. I usually print this with a raft or a brim since there's not much touching the build plate. ...3in...