hyperlite evo hd 3d models
19513 3d models found related to hyperlite evo hd.thingiverse
This is an antenna mount for the Hyperlite Evo HD frame. I use TBS unify so the antenna mounting holes are for that. ... If you are interested in other file formats to more easily modify and create your own tweaks, try this...
thingiverse
One of many antenna mount versions that I came up with for the Hyperlite Evo HD, but ultimately decided against for something a little sleeker. ...Print Settings Printer Brand: Wanhao ...
thingiverse
I have a Hyperlite Evo HD that I would eventually like to mount an HD camera on. BMC3D and Brain3D have great designs for this frame, but I wanted a file that I could work with and tweak as I would like to try and squish my battery and HD camera on...
thingiverse
... flex with the cables, just slide it in spacers, zip ties hold everything together pretty well. ... Set: https://www.thingiverse.com/Toily/collections/pirofliprc-hyperlite-evolution-evo-hd-toily-set-v12 ![Toily set](http://i.imgur.com/4jN93Nw.jpg?1)
thingiverse
This is a mount for Lumenier AXII antennas with MMCX or u.FL connectors. It slides around the back of your top plate and screws in using the two rear standoff screws. I designed it to work with my frame configuration as I have an LED/buzzer board...
thingiverse
I'll be running my EVO over concrete, so this should protect it from scratches at least. ... Set: https://www.thingiverse.com/Toily/collections/pirofliprc-hyperlite-evolution-evo-hd-toily-set-v12 ![Toily set](http://i.imgur.com/4jN93Nw.jpg?1)
thingiverse
... through it grips, you can secure the cam using the screws or a zip tie (way faster to swap). ... Set: https://www.thingiverse.com/Toily/collections/pirofliprc-hyperlite-evolution-evo-hd-toily-set-v12 ![Toily set](http://i.imgur.com/4jN93Nw.jpg?1)
thingiverse
This is a mount for a Strix Hoot antenna with an MMCX connector. It slides around the back of your top plate and screws in using the two rear standoff screws. I designed it to work with my frame configuration as I have an LED/buzzer board mounted to...
thingiverse
i made this. it's a mount of the vtx that holds it by the corners for the intended mounting location. this prevents problems caused by attaching the heatsink to a surface like overheating and excess vibration. I'd add a small slice of .25mm...
thingiverse
I liked the design of this https://www.thingiverse.com/thing:2834895 mount but i wanted to be able to attach antenna tubes to it. I drew this in solidworks referencing the design of the one linked. Then antenna tubes are tight to install but that...
thingiverse
... the back plate, also you can cut them and use the antenna mounts independently in other spacers. ... Set: https://www.thingiverse.com/Toily/collections/pirofliprc-hyperlite-evolution-evo-hd-toily-set-v12 ![Toily set](http://i.imgur.com/4jN93Nw.jpg?1)
thingiverse
25 Degree camera mount for the top plate of the Hyperlite EVO HD. Print with PLA / ABS. You can edit this mount to fit to your quad: https://www.tinkercad.com/things/cCbwrzEd5bW The mount was designed to fit perfectly to my GoPro Session Sleeve...
thingiverse
I wanted a secure way to mount a TBS Unify Race HV to my new HyperLite EVO frame. I whipped up this sling to do the job. Print this in TPU. Use electrical tape to attach the vtx to the sling and slide over the middle standoffs. The sling will grip...
thingiverse
This was made with permission and source from [jwalter748's](http://www.thingiverse.com/jwalter748/about) [ Hyperlite top plate angled washer](http://www.thingiverse.com/thing:2153318). I closed off the ends and added bits to add antenna tubes. I...
thingiverse
Miscellaneous parts for the Apex Evo & HD frames. Print them all at 100% infill or 99 walls, use supports for the O3 antenna mount. ... Included is: O3 Antenna mount (basically the same as the original) O3 Stubby Antenna mount RX Antenna mount based off...
thingiverse
Basic fullsize and mini camera mount for the Hyperlite EVO, Hyperlite FLOSS and the Hyperlite FLOSS 2...as well as any 30.5x30.5 standoff mount.
thingiverse
hyperlite couch mount with placement for tbs immortla T antenna
thingiverse
needed a 35 degree a run cam mini swift for my evo. ...I haven't tested this yet though, let me know in the comments if these work.
thingiverse
This is a mod for the Superlux HD-681 Evo that helps you fix the issue these headphones experience after a short while (the cable plug for the replaceable jacks gets easily worn out and cuts at the top part of the rubber cover). Install it by...
thingiverse
This is a couch mount that I needed for my Hyperlite Evo. I didn't want to design a mount for the front of the top plate, so I ended up making one for the posterior portion. Here are the following parameters: 1. 35-degree cam angle; back-rest at...
thingiverse
# Superlux HD-681 Evo Headphone Mod ##### The Superlux HD-681 Evo are awesome Headphones to a very low price. The only problem they have is the little cable with the jack plug on the left side. ##### After about two years in extensive use and...
thingiverse
As of september 2019, this frame should be excellent for a micro HD quadcopter build using one of the new nano HD cameras that are being released. Check below for recommended hardware. This frame was thought as a 2S machine but you can go 3S/4S,...
thingiverse
... 35 degree go pro mount for an fpv quad copter. Currently used on a hyperlite evo HD, mode 2 ghost, and Rebellion Lite Keep infill > 25% __ EDIT: volume of box is large, use foam tape on inside to prevent jello. ...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58413 Instructions Using the following options: elipseSize = [size * ratio,size,height] initials = HD letter_height = 1 height = 3
thingiverse
this is a remix from another antenna mount i found on thingiverse by lancelotfpv for the hyperlite evo hd that i keep modifying to fit different frames. original file for the evohd at this link https://www.thingiverse.com/thing:2298627 thanks to...