hypertherm 220478 3d models
32 3d models found related to hypertherm 220478.thingiverse
Pointer for Hypertherm plasma machine torch. Flip model so the point is facing up, add supports. ...
grabcad
A rough rendering of the Hypertherm Powermax 45, close to exact dimensions
thingiverse
Simple offset guide for Hypertherm 45XP 75 degree plasma cutter hand torch and standard shield. Use this as a spacer between the cut line and the straight edge against which you will hold the torch to set the straight edge at the right distance...
thingiverse
This is a mount for two laser from Harbor Freight for an older Hypertherm Duramax45 plasma machine torch. The clamp uses a 1/4-20 threaded insert, and 8-32 screws for the lasers itself. I printed it with no supports and a brim. The torch radius is...
cults3d
This cap protects the power supply end of a Hypertherm Powermax plasma torch cable. Specifically, I have tested this to fit on a PowerMax 65, though it should fit on 45, 85, 105, etc. also. This is especially useful if you have both a hand torch...
thingiverse
This cap protects the power supply end of a Hypertherm Powermax plasma torch cable. Specifically, I have tested this to fit on a PowerMax 65, though it should fit on 45, 85, 105, etc. also. This is especially useful if you have both a hand torch and...
prusaprinters
also. This is especially useful if you have both a hand torch and a CNC machine torch, so that you can protect the delicate air fittings of the torch that is not in use. Why an $800 torch doesn't come with one of these from the factory is a mystery...
thingiverse
A super quick print to add 2 9mm straight line lasers to a hypertherm machine torch. This attaches to the torch body so you can still change consumables. ... If using for Langmuir Crossfire Pro I ran the wires into the control box and used a 36v to 5v...
thingiverse
A plasma torch holder for the MPCNC It has been designed to fit a Hyperthem torch for a Powermax 30 the ID is 25.5mm (an inch for the 3rd world measurement systems)
thingiverse
heavy duty machine torch clamp... printed in PETG with 6 walls and a very high infill rate. ... -10 ruthex M5 inserts are needed!
thingiverse
laser center finder for ppllc gantry with magnetic breakaway inexpensive laser with 2 AA batteries and a piece of wire or tinfoil for contacts attaches to mag breakaway on precision plasma table gantry with hypertherm machine torch easy on\off twist...
sketchfab
... 50%. New ease-of-use features and engineered system optimization make the XPR300 easier to run with minimal operator intervention, while also ensuring optimal performance and unmatched reliability. https://www.hypertherm.com/hypertherm/xpr/xpr300/
sketchfab
... 50%. New ease-of-use features and engineered system optimization make the XPR300 easier to run with minimal operator intervention, while also ensuring optimal performance and unmatched reliability. https://www.hypertherm.com/hypertherm/xpr/xpr300/
sketchfab
... 50%. New ease-of-use features and engineered system optimization make the XPR300 easier to run with minimal operator intervention, while also ensuring optimal performance and unmatched reliability. https://www.hypertherm.com/hypertherm/xpr/xpr300/
thingiverse
... steel plate. 4-12mm sizes 1mm incriments. Instructions Cut on Torchmate CNC plasma table 12mm mild steel plate. Torch Hypertherm Powermax45 45 amps power 15 ipm cut speed 2.5 minutes cut time.
thingiverse
This is an insert tray to use a small altoids tin as a protective case for the 40A consumables for a Hypertherm 1250 plasma cutting torch, as used on the Dynatorch CNC plasma cutter at MakeIt Labs in Nashua, NH. ... The consumable part numbers, for...
thingiverse
my plasma is a hypertherm xp45. it should work with any plasma cutter with a 1" torch. you will need a small spring. I found in an assortment pack from amazon. the spring measures roughly 9mmx35mm (It is called out in the box as 23/64" x 1 3/8") ...
thingiverse
This is a remix of this thing : https://www.thingiverse.com/thing:2516238 by Planet CNC I just modified the "moveable" part in order to put 2 torch holder that fits with hypertherm mechanized torch ( 35mm aprox.). I also designed a cable holder if...
thingiverse
Gage to set the straight edge to do a hand drag cut with a Hypertherm Powermax 30XP hand torch with a general purpose drag tip. Offset is 3.81mm and this little tool allows me to draw a line precisely where I want the edge of the plate. Set the...
thingiverse
This is a floating Z torch mount for the LowRider v2 CNC by Allted (https://www.thingiverse.com/thing:3026040) The torch carriage is designed for a Hypertherm Powermax 45xp machine torch. The carriage is a tight friction fit, meant to be sanded until...