ibm model
1779251 3d models found related to ibm model.thingiverse
PLA foots for the good old IBM Model M Keyboard. ... On Github: https://github.com/h0sch180/3D_Print_Things
thingiverse
Leg for the best mechanical keyboard ever created, the IBM Model-M. I have notice of other leg model, but I have three of those keyboards and all have this kind. ...
thingiverse
ibm model f replacement badge, dimensions are around 19x19mm
thingiverse
Scaled down the model to 13mm wide removed tab on side for use in IBM Model M2 model 1395300
thingiverse
This is a screwdriver for an IBM Model M keyboard. ... Recommendet print-settings: PLA or PETG 0,2mm Resolutioin 50% Infill
thingiverse
Replacement foot for IBM Model F XT. May not be 100% dimensionally accurate as compared with stock. I'd recommend printing two and replacing both. ...That plastic IBM used in the 80s would be impossible to match 3d printing anyway.
thingiverse
Standard cap for IBM Model M keyboard. I use it right now. ... Model found here: https://github.com/jaseg/Model-M Do not mind my ugly writing on the cap :)
thingiverse
Replacement feet for IBM Model F XT, should work on other model Fs, but I haven't tried it. V1 is dimensionally the same as the original part, I might make another version that's stronger. ...I also included a step file in case someone wanted to put a...
thingiverse
My IBM Model M was missing some keycaps, so I wanted to 3d print some. I found some models on the Internet, but they either didn't fit or didn't look very good. So, I decided to make my own. I used an SLA resin printer to print those, I'm not sure...
prusaprinters
The IBM Model M is great, but the little clips on their SDL cables tend to break. Once this happens, the cable doesn't like to stay in the keyboard. Replacement cables are really expensive! Instead, this clip slides over your connector and screws...
thingiverse
Model found here: https://github.com/jaseg/Model-M Not tested and this is not the Enter key for my Model M, maybe an older version pre 90's.
thingiverse
Model found here: https://github.com/jaseg/Model-M Not Tested This looks like a normal base key, I do not have a shift this mall or in this form. ...Uploaded for completeness, check the Shift Wide for the other shift.
3docean
Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) - *.obj (Multi Format) - *.3ds (Multi Format) - *.mb (Maya 8.5) - *.lwo (Lightwave 6) - *.c4d (Cinema 4D 11) renders Are made in 3ds Max 2008 using...
thingiverse
ibm model m key cap holder, for better typing experience when one of these is missing. ... You can make a few ajustelment by using scissors.
thingiverse
Replacement folding foot for a classic IBM Model M keyboard. Includes the bump on the axle so that the foot remains propped even if the keyboard is moved. ...
thingiverse
Replacement foot and spring retainer for IBM model-f AT keyboard. Kept as close to the original as possible (pictures show comparison to original foot). ...If your spring is missing you'll need an approximately 44mm long by 10mm diameter spring.
thingiverse
IBM Model F AT protective foam inserts for a 54 X 38 X 11 box. You can customize it to the size of your box and get it cut locally. ... This project is untested, it is your responsibility to check the files, and I can't be responsible for any...
thingiverse
I've added an extension to place in the middle, so it will be wide enough to fit an IBM Model M (49 cm). Print the 2 halves and the extension, then put the extension in the middle and glue the 3 pieces together. ...I used a hot glue gun, superglue...
thingiverse
This is the IBM Model M "M-Deck" as I like to call it. I had seen a lot of cyberdecks online and thought it would be cool to make my own. Beyond that, I thought it would be cool to make a retro looking one. When searching online i really couldn't...
thingiverse
replacement feets for the model m122 the short ones are the same dimensions as the stock ones and the 2 others are longer and should still fit flush when closed