ideaformer ir 3 3d models

Link: https://www.thingiverse.com/thing:2271321 The original IR Mount didn't got low enough for my printer and this one is much less flexible. Also this version doesn't need nuts, the screws are hold tightly by the plastic itself! Z Offset for me is...

Essentially: 1 Freaduino Uno board (Compatible with Arduino Uno) 1 HC-SR04 IR sensor 2 SM-S4303R continuous rotation servos 1 buzzer 2 LEDs with mounting hardware 1 9V battery and connector M3 Allen head screws, small screws, and torque bushings of...

This custom design fits my model of the pi cam perfectly and allows it to breathe with its three photovoltaic sensors, one on each IR blaster and one on the main board. The third hole, previously blocked by the case, is now accessible. To complete...

This IR beacon can be mounted so that a robot can follow it, or used with a TV-Be-gone type of device for hands-free control. Additionally, LEDs can be added for a 360-degree light show. The possibilities for use are endless; it's up to you! Check...

... Furthermore, I added air holes to the back body of the camera to enhance cooling efficiency, as IR spots tend to get extremely warm during operation. This redesigned stand allows for a completely print-able camera without any supports required.

I design an optical sensor mount that seamlessly integrates normal 5mm LEDs, utilizing Osram Opto SFH 203 visual light and near IR sensors to enable the use of common red 5mm LEDs. However, you can choose any pair of LEDs that fit within a 5mm...

3D Scanner IR Distance Sensor is a device capable of creating high-resolution, accurate digital 3D models of real-world objects with precision. This scanner utilizes stereo vision, typically two digital imaging systems, and structured light...

Firstly, the IR Mount on my E3D V6 hotend was causing unstable results, leading me to search for an alternative. The second issue was with my half-circular fan duct, which wasn't providing the airflow I needed. To address these problems, I...

I recently got the Inverted IR Sensor with an blue LED. ...The LED is great for dialing the lever in but its pretty bright. Since I sleep in the same room where my printer is and I don't want to sleep under broad daylight (Slightly exaggerated) I...

Most xTool IR Modules do not focus correctly using the included focus bar. You can print this bar (recommend with a resin printer), remove the metal focus bar and replace with this one. Just remove the screws at the back of the module, remove the...

I'm a Simple Sharp IR Bracket, Designed to Mount on a 9 Gram Servo. Fast Printing and Easy Modification Make This Project a Breeze. A Solid Model Is Provided Below in Solidworks 2010. Print the Bracket. Next, Bend It to the Designed Angle. Here's a...

This Universal IR Sensor Probe Mount is a board mount designed specifically for the sensor board from MiscSolutions. It has been engineered around a Ultimate Greg's Wade's Extruder with a J-Head MK IV-B, but can be adapted to anything with a groove...

I'd like to give a quick shout out to user Kevinlo for designing the camera back plate for his IR camera project. I used it in conjunction with my top piece to make this project. Thanks for letting me re-publish your part! Here is the mounting...

Potential future improvements include: - Adding reset button access - Integrating RF capabilities - Developing an external adaptor for 360-degree infrared operation with wires through the current IR led hole A photograph illustrating the setup is...

Die Stromversorgung stellt ein 3,7 Volt LiPo Akku sicher, die Ausgangsspannung wird über einen Step-Up-Converter...

To achieve precise measurements, the board is positioned slightly off-center, aligning the IR reading point perfectly with the nozzle. This setup minimizes the Y offset to 16mm and eliminates any X offset, resulting in more accurate temperature...

own createt from measurements of the cam. ... i have printed 3 parts from here and nothing fits with my Pi-CAM

The smaller one is approximately 1 10/16 inches wide by 3 3/16 inches deep. This is a wall-mounted LED remote holder designed to be attached with fun tack or velcro. Originally, I intended to add screw holes for secure mounting, but this design was...

LOOK NO FURTHER. The size of the biggest main slot is: "2 1/4 inches wide* 3 14/16 inches deep" The smaller one would be: "~1 10/16 inches wide* 3 3/16 inches deep" This is a LED remote holder meant to be mounted on walls with fun tack. I originally...

The largest slot measures up to: "2 1/4 inches wide * 3 14/16 inches deep" While the smaller one is: "~1 10/16 inches wide * 3 3/16 inches deep" This nifty LED remote holder is designed for wall mounting using fun tack. I initially envisioned adding...

The largest main slot measures: 2 1/4 inches wide * 3 14/16 inches deep Meanwhile, the smaller one is: 1 10/16 inches wide * 3 3/16 inches deep This clever LED remote holder is designed to be mounted on walls with fun tack. I initially planned to...

... The gcode file is specifically designed for an Ender 3. For optimal results, slice your own design, but if time is of the essence, it should print in about 40 minutes with support from the attached Ender 3-specific gcode. ... Best regards, Joe

To ensure optimal results, we recommend slicing your own design; however, if time constraints are a pressing issue, the attached G-code should print in approximately 40 minutes with support structures intact when used on an Ender 3 only. ... Best...

I designed a novel prosthetic limb for seamless integration with the Ender 3 and CR-10 3D printers, providing users with a functional solution to their print needs. ...By contributing my time and expertise, I hope to give back to the community that has...

... Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1238620 Instructions Using the following settings: Depth: 6 units Width: 33 units Clamp Depth: 3 units Clamp Notch: 1 unit Height: 85 units Clamp Position: 30% Polygon Count: 100

... the original mount 2. Take out the magnet part from the stock mount. 3. Put the magnet into the printed mount. 4. Fix printed mount with 4x M2.6x8mm tapping screws. 5. Attach the printed mount on monitor top with double-sided tape. ...

Needed additionally: - Hardware as seen in MrBlackMagic video (pi, batterypack, screen, sensor) - 2x 4mm bolt 30mm long (round or hex head, part 7 or 7a) + 2x m4 nut (hex) - 2x 6mm bolt 30mm long (hex + hexnuts) - 6x 4mm bolt 18mm long (round...

The two ear cutouts for mounting the sensor should be 3.36mm, if that helps you source matching hardware. I edited my design: I used some 4mm diameter by 25mm length screws instead and adjusted their threads accordingly. Additionally, I removed the...

Imitation of the MICA IR missile for rocketry.29 mm engineScale : 1:3 (~1 m high)