iec320 3d models
303 3d models found related to iec320.grabcad
From Amazon.com: https://www.amazon.com/gp/product/B00NWO68JI/ref=oh_aui_detailpage_o03_s01?ie=UTF8&psc=1 "URBEST 10A 250V AC Rocker Switch 3 Pin IEC320 C14 Inlet Module Plug Fuse" Please let me know if there are any mistakes or if you have any...
prusaprinters
Created this IEC320-C14 bracket to support my enclosure and provide a little more support when going through side of enclosure
thingiverse
... depending on how paranoid you are. Once the mount is assembled attach it to the 3030 with two m5 screws + hammer nuts - Print face down - Required Materials * 2x M4 screws * 2x M4 nuts * 1x IEC320-C14 recectacle * 2x M5 screws * 2x M5 hammer nuts
thingiverse
... whipped one up. ... This will take an IEC320-C14 power inlet (Plug in, fuse, switch) with horizontal mounting holes (most I found were vertical). Mount switch with M3 BHCS. ... Holes for mounting to 2040/4040 extrusion with M3 screws and hammer nuts.
thingiverse
... hole a little to fit (deliberately very tight to snap in). Search on Amazon or ebay for: "3 Pin IEC320 C14 Inlet Male Power Socket w Fuse Switch" While you are out, pick up a fuse, this switch does not come with one. ...See attached wiring diagram.
thingiverse
If You enjoyed this project and You want to say "Thank You" please consider supporting me by sending a tip on thingiverse or my PayPal here. IEC320 cover which I have designed for RatRig V-Core enclosure. ...
prusaprinters
Quick and dirty, simple power panel for the Mendelmax. Print instructionsCategory: 3D Printer Parts Instructions Print, file switch hole a little to fit (deliberately very tight to snap in). Search on Amazon or ebay for: "3 Pin IEC320 C14 Inlet Male...
thingiverse
For use with macbook pro chargers. ...My charger wouldn't fit in university plugs due to weird angles and I didn't want to use the long cable. Enables most IEC320 C7 cables to be used safely.
prusaprinters
A dust cover for an IEC320 C14 Receptacle. ...Even though the friction fit is good, a cutout has been added to keep the cover attached, using a string or similar, when not in use.</p><h3><strong>Print instructions</strong></h3><p>Material:...
prusaprinters
I made this for my RatRig V-Core3 printers with safety in mind but can oc be used with any 3030 extrusion or similar.6 Countersunk M3 screws, approximately 6-8mm long6 Heat insertsIt is 4mm thick where it attaches to the 3030 extrusion so M6x12mm Cap...
thingiverse
A simple bracket for a fused power socket for the IEC320 C14 type cord. This bracket was designed to accommodate the corner brackets used in the BLV mgn Cube. The back is open but the recess is deep please use caution with the crimps used. Thick...
thingiverse
I have used several of these IEC320 C14 socket/fuse/switch assemblies in my projects and one thing I found out is: Don't snap the switch into place until you're ready. It's very difficult to remove. After much too long struggling with the...
thingiverse
case for panel IEC320 C14 Power socket for https://www.aliexpress.com/item/Panel-IEC320-C14-Inlet-Power-Socket-On-Off-SPST-Red-Rocker-Switch-AC-250V-10A/32652985391.html?spm=a2g0s.9042311.0.0.27424c4dR6xgbQ
thingiverse
Apple 1 - Transformer Switch with Fuse Box IEC320 Enlarged the cable pass-thru Added Apple Computer 1 script Cut the lip at the bottom
thingiverse
This is a remixed version of IEC320 C14 AC Power Switch Case adapted to 2020 aluminium profile. ...It is designed to put AC Power switch in the corner, on top of aluminium profile's angle linker.
prusaprinters
<p>Just a quick and simple model. ...It's a rocker switch plug for IEC320 C14 socket meant to plug in the hole for the rocker switch in case you don't want to have it there.
thingiverse
This is a dust plug that fits an IEC320 C14 receptacle (typical PC power supply inlet) At some point I'll need to figure out some sort of "keeper" or hinge but this snugly fits as it is now. I printed this in TPU but I would think PLA would be just...
thingiverse
This is an enclosure to mount [this IEC320 C14 fuse and switch combo](https://www.amazon.com/gp/product/B07RQV2NPN/) onto the back of the 4040 rails on a Mega Zero. I did additionally have to tap threads into the rear of the 4040 extrusion, as the...
thingiverse
Some IEC320 C14 inlet power modules do not come with an extended outer plate with mounting screw holes so I made this simple part to add this mounting option. The mounting holes are in the standard positions for this type of power inlet module so...
cults3d
Information de ce projet : Je n'ai pas trouvé une box qui correspondait à mes attentes et j'ai réalisé celle-ci pour une table IKEA Lack Suivi du projet : V0.0 : Création Matériel nécessaire : Prise IEC320-C14 AC08 4 vis à bois 2 vis M3 (Installation...
thingiverse
Information de ce projet : -- Je n'ai pas trouvé une box qui correspondait à mes attentes et j'ai réalisé celle-ci pour une table IKEA Lack Suivi du projet : -- - V0.0 : Création Matériel nécessaire : -- - Prise IEC320-C14 AC08 - 4 vis à bois - 2 vis...
thingiverse
Case for IEC320 C14 switched and fused Inlet. The inlet part is pushed in and locked with four notches. The fit is very tight, so it will be securely trapped in the case. You will barely get it out again. In the bottom is a tunnel for an cable tie...