ikea shelf boxes 3d models

The lathe and plaster walls were giving me a run for my money, combined with shelf mounts designed by Goldilocks (screws had to be JUST RIGHT in size and spacing) that made me want to pull my hair out. A voice in the back of my head was screaming...

Headphone holder with a custom hook for the Ikea Mosslanda shelf.The shelf lip is ~12.7mm (~½ Inches), to fit snuggly, I designed the clip to be 12.65mm.There are multiple variants for different headphones sizes:Very large: fits headphones with...

This shelf is designed specifically to hold a Razer Core X eGPU and is sized to fit the legs of the Ikea Bekant desk frame, but it could also be used to hold a SFF PC case. There are holes sized to accommodate 1 inch wide straps if extra security is...

The "nub" is located on the side where you drill (initially using a hole punch) a small hole to then screw in (the screw is supplied with Ikea's lightbar packaging). You'll need to trim off several mm of the tip of the screw after initially screwing...

Small shelf that fits in a Ikea headboard to hold a diffuser and hides the power cable behind the headboard. It has a ring to keep the diffuser from sliding off while maintaining a slim profile. Also a small hole in the base to pass through the power...

Its not only neat, but it is actually easier to pack and unpack it, while hanging.If you don't need the shelf, but like the hook I got you covered- JustHook.stl is what you need.There are two parts: shelf and hook. It uses the screw that is already...

Remix for smaller boxes (ikea moppe).

Ikea Rudsta bracket to give extra height to the shelves

A headphones holder for the Ikea Lack shelf.The cable clips are for a 4mm cable, which is the one that uses my DT 770 PRO.I also include the M, the first letter of my nickname.It took 1h 45min to print on my Ender 3 Pro, with supports.Print...

In the remix the width of the clamp was reduced by 9mm to fit Ikea shelves.Shelf thickness is 26mm.Print SettingsPrinter Brand:PrusaPrinter: I3 MK3SRafts:NoSupports: NoResolution:200Infill: 100%Filament: eSUN PLA+...

That's where this component comes in - it fills a crucial gap by allowing a standard shelf to be placed directly atop a cabinet, eliminating the need for makeshift solutions or imperfect arrangements. To create this part effectively, you'll need...

Replacement Komplement Shelf Pin/Bracket for PAX cabinets

Just made the drip shelf skadis compatible. ...Print on shelf surface and use supports for the pegs.

A shelf for post-it notes that fits CSD_salzburgs glorious shelf hook. I.e. ...x2 of https://cdn.thingiverse.com/assets/6f/cf/25/a1/97/Skadis_Shelf_Hook.stl

The compact shelving unit perfectly complements the IKEA Malm bed's sleek design.

Ikea's IVAR shelf system is extremely customizable, but a little bit floppy even with the included OBSERVATOR cross-brace. We wanted to add some more stability, so I created some struts to attach to the back of the shelf. The four screw holes that...

This bracket is to provide extra support for the shelf in the Kleppstad wardrobe.

Just a replacement for shelf brackets that got lost during moving.

Simple LACK shelf cable management that uses a 27mm wide velcro strap to hold cables.

Shelf for the common Tesa dispenser. ... Prints without supports without any problems.

For storing bobbins of sewing machines on the IKEA Skadis pegboard. I designed it to be easy to print, no support required. ... See my other accessories for IKEA SKADIS pegboard.

We're making a simple conversion here to convert one or two IKEA Omar bookshelves into a sideboard quickly. ...With these connection pieces, you can attach a worktop to one or two IKEA Omar shelves.

If you're looking to repurpose your IKEA Hejne shelving unit into a compact wardrobe, it's definitely possible.

I've crafted a device specifically intended to prevent tiny vehicles from plummeting off the edge of a shelf.

Replaces the small knob that holds up a shelf and distributes the load over a larger area.In my case the shelf broke and I needed to replace the knob that holds the shelf with something larger.Print it with the flat side down, put the small metal...

Product : IKEA, EKBY HEMNES (790 x 190 x 18 mm) ----- 2017.11.09 ----- I created two new accessories for this stand. ... Magnetic iPhone cradle for monitor stand https://www.thingiverse.com/thing:2633316 Tablet cradle for monitor stand...

Print Shelf and hook an than glue it. I have print all in PLA. ... You can modify mesure in STEP file

I wanted a monitor stand for my desk and had some Billy shelfs laying around. I therefor craeted some slot on feet to make a raised stand. It is printed in two parts for it to fit on my ender-3. It has some screw holes to fix it to the shelf. ...

Shelf with 7 shelves and boxes for small parts, such as screws. Suitable for model railroad in H0, but can of course be scaled larger. ... 2 STL files: 1x with supports and 1x without supports

Having several boxes of various wraps on a pantry shelf seemed messy, disorganized, space inefficient, and risks damaging the boxes. So here is a shelf organizer meant for storing wrap boxes such as Cling Wrap, Handi-Wrap, Reynold's Wrap, Parchment...