ikea symfonisk bookshelf 3d models

First when I realized my PETG filaments are getting wet, creating all kind of problems, I decided to build a drybox for them.It is based on an 10.6 liter sized IKEA box (792.767.60) which is big enough and has a rubber sealing for better performance....

Unfortunately, I won't be able to try printing it now because I'm in the middle of updating my IKEA pendant lamp and need to print 84 white PETG parts, so there will be no other colors in my nozzle for the next two weeks. I recommend printing with a...

Ich hatte im Keller ein Brett aus OSB und ein IKEA Regal. Mein Raspberry Pi hatte ich dabei mir diesen Teilen (https://www.thingiverse.com/thing:4557789/) an der Wand montiert. Jedoch brauchte ich zunehmend Platz und das Kabelmanagement wurde...

The desk shown in the photos is the 'Linnmon' table top from Ikea which comes in at a width of 34mm. Printing: Supports: Not needed Layer Height: 0.15 (as seen in the pictures, can be printed at 0.2) - larger layers may make the print weaker around...

This is a stand off for mounting my Ender 3 v2's power supply on the underside of my Ikea Lack enclosure.Print twoPSU Secures to the mounts with 4 m3x8 cap screw. The mount then is secured to the enclosure by some screws I found in my garage. ...The...

### Besides printed parts you will need: SAMLA box 11 liters from Ikea with clips (link to 3D printed versions I am using below) 3x 3m x 10mm screws 4x 4m x 25mm screws 8x 3m x 20mm screws 2x M4 nuts Pneumatic bowden fitting PTFE tubing Rubber...

An IKEA “HEMMA” light cord fits nicely into the hole, then the other end of the cylinder fits over the inner part of the spool just like the “spider”. Since both “spider” and light-fitting cylinder mount on the spool flange they can't both be...

First when I realized my PETG filaments are getting wet, creating all kind of problems, I decided to build a drybox for them.It is based on an 10.6 liter sized IKEA box (792.767.60) which is big enough and has a rubber sealing for better performance....

Probably only works well with thick tables like the Ikea Lack. Redesigned the holding part, reusing the excellent (https://www.thingiverse.com/thing:1031950) clamp part from the headphone hanger, which I printed some time ago and which is one of the...

As You Can See from the Pictures, the FBCCS2k is Mounted Under an Ikea Lack Table, Which Helps Optimize Filament Guidance from the Spool to the MMU2S. This Results in No Twists or Tangles. The PTFE-tube Measures 4mm Outside and 2mm Inside, Similar...

I had a really good experience with the Ikea Jansjö lamp with a clip, clipped on the top of the spool holder. But the light strip was still in the play.</p><p>I spotted a cheap set in Lidl (<a...

You can easily get the sockets with cord and switch on Amazon, Ikea or your local hardware store. Check the provided images to decide which version to print. Choose the base according to your socket and the head according to your preference on...

I already had some of these lights for the Ikea Lack table enclosures I had previously.https://www.amazon.com/gp/product/B0737Y29ZV/ref=oh\_aui\_detailpage\_o05\_s00?ie=UTF8&amp;psc=1So I bought a few more and designed a bracket that would hold these...

Those are separate beacause they should be able to be easily removed when its necessary to change the bulb. It is designed to fit the IKEA HEMMA through the hole in the top panel. Because the pieces are so light, you wont spend much filament on doing...

All the common solutions such as Ikea Lack, photo tent and custom acrylics did not cater that well. Besides they never serve larger volume printer like this mega X. To provide dust cover and constant heating in some prints, a cover still seems...

Love that stuff, I've had more trouble with PLA to be honest ...Print SettingsPrinter Brand:Creality Printer: CR-10SRafts: No Supports: NoResolution: 0.2 mm Infill: 15% Notes:Material:Transparent PETG (NuNus)Printer settings:235°C nozzle temp60°C bed...

This is a large but simple diorama base for a Kenner Jabba that can fit on an Ikea Detolf shelf and kind of fill in the whole thing. The measurements of the walls are slightly too large for my 12x12 printer so I split it into two pieces; you may need...

Mount this on any surface near an outlet and reclaim your bathroom counter space once and for all!The attached image shows the mount fixed to the side of an IKEA GODMORGON mirror (MDF with a reflective foil surface) by a single 4 x 16 mm countersunk...

You could also add thicker pads here to accommodate thinner edges. For reference, I designed this hanger to clamp on to the edge of an IKEA Gerton table top that serves as my desk. So the flattened lobe cam fits and adds the right amount of clamping...

x 1/16” and 5/16” x 1/16” (I purchased from K&amp;J Magnetics)ScrewsSuper glueAdditional designs used:Spool holder: https://www.thingiverse.com/thing:2486632Filament guide: https://www.thingiverse.com/thing:2228361Ikea Lack Grommet:...

This is a SNES cartridge holder for NTSC (North America or Japan) cartridges that will fit up 60 cartridges in a (slightly modified) IKEA Kallax cube shelf. ###Files 6 Slot - the basic cartridge holder, can hold 6 cartridges Dovetail -...

Something like the ones IKEA offers.The lower bounds for the rods are necessary as you need about 5mm clearance when installing the brackets on the wall. This way, you can turn the mount downwards such that it's not in the way when screwing it into...

The FBCCS2k is actually under a Ikea Lack table. Therefore the guidance of the filament is optimized from the spool to the MMU2S (no twists). The PTFE-tube is 4mm outside and 2mm inside, like those from Prusa Printers. The screws to hold the tubes...

I mounted my ArcaWalls with 3 wood screws into an Ikea cupboard, that way it's plenty strong for my heaviest camera, an APS-C D5300 that weighs ~1kg with my largest lens.I included two guide holes in case you wanted to mount your ArcaWall with 4...

There was only one problem with their design - it was for IKEA Skadis style pegboard and we don't have that type in our edu-makerspace. So into Fusion360 I went to design my own! I knew that I wanted these to be stored on a Wall Control board...

All the color changes are height based color swaps so no MMU required!The card kit was designed to hold and ikea tea light (Glimma), which are ~39 mm in diameter. When assembled the hearts all line up and with the candle in the center. It is designed...

Generating Attributions log: [0] Thing Title: Puzzle Mask [0] Thing URL: http://www.thingiverse.com/thing:93210 [0] Thing Author: Cerberus [0] Thing License: Creative Commons - Attribution - Non-Commercial [1] Thing Title: Bottle Holder [1] Thing...

Printer on top of cabinet with side walls: http://www.thingiverse.com/thing:56737 Magnetic tool holder - AKA steel ;-) Strong small magnets Ikea LED light LED strips with dual (12 & 5VDC power supply) Small no-break for printer and dehumidifier only....

This is my design for a bedside lamp where I have used a WiFi WLED controller to upcycle an old lamp (I think it is an old Ikea lamp). This includes all the 3D printed parts and the circuit diagram with PCB that should be fine to produce. It's all...

About this projectI built a TV set wall with IKEA cabinets with long (80cm) doors held by only two hinges. The momentum put on those hinges makes the doors sag over time. Additionally, my kids are not always careful operating those doors putting...