immersionrc 600mw 5.8 ghz 3d models

This is a vertical TX case I use for my 250 size quad-copter.

I have been using the case remixed from http://www.thingiverse.com/wezze wanted to fold it to make more room.

Pod for a small SurveilZone 600tvl camera and an ImmersionRC 600mw 5.8 GHz transmitter used as a video downlink for FPV model flying. Camera: DC5V~22V Plastic Case mini 600tvl Sony Super HAD CCD Super FPV Camera available from SurveilZone. IRC...

This is a mount for Fat Shark (ImmersionRC) 600mW Video 5.8 Ghz transmitter for DJI Phantom for FPV (First Person View) . ... Remixed from http://www.thingiverse.com/thing:99048 This edition is smaller and has a different antenna hole

NOTE: 3/31/2015 I based the dimensions of the antenna area off of my ImmersionRC 5.8GHz SpiroNET Antenna set. The nut size of the antenna specifically. Your antenna nut size may be slightly larger. In Version 1b I will make this area larger. ...

ImmersionRC 5.8Ghz Audio/Video Transmitter (FatShark compatible) 600mw Tx case. Protects tx while allowing cooling air flow. Supports antenna mount and prints easily with no supports. Adds flat surfaces to Velcro to. ... Check out my new design for...

ImmersionRC 5.8Ghz Audio/Video Transmitter (FatShark compatible) 600mw Tx case. Protects tx while allowing cooling air flow. Supports antenna mount and prints easily with no supports. Adds flat surfaces to Velcro to. ... Check out my new design for...

ImmersionRC 5.8Ghz Audio/Video Transmitter (FatShark compatible) 600mw Tx case. This split case provides much more support to the antenna mount then the one piece design. Designed for 3 zip ties, I used 1 zip tie and two bands of electrical tape so...

ImmersionRC 5.8Ghz Audio/Video Transmitter (FatShark compatible) 600mw Tx case. This split case provides much more support to the antenna mount then the one piece design. Designed for 3 zip ties, I used 1 zip tie and two bands of electrical tape so...

Edit it online https://www.tinkercad.com/things/0kEsmZUv19u its a different bottom piece for 5.8ghz clover antennas, fits the nicely made ones by TrueRc or Aerial Video systems , its not for an antena with a sma connector, put the cover on , a newly...

This is a video transmitter case designed for an ImmersionRC 600mw video transmitter.

Protection holder for the ImmersionRC 600mw vTX. Strap it down using ziptie's and the antenna plug should get a really hard time coming of in a crash. Mount the case using double sided gel tape. This is not the final version. I have a version with a...

Antena 5.8 GHz 3dBi for video transmitters, FPV systems in drones.

Helical antenna for 5.8 GHz, designed in CATIA. Print out the mandrel and antenna support, then wrap a solid copper wire around it in the groove. Twist the wire into the support, solder a connector and backing plane on, and it should work. Some...

5.8ghz antenna cover Instructions you need to print this in 0.2 hight 50 mps and snap together the bottom and the top Piece and if tou need you can gleu the bottom piese to the antenna

This is Version 1 of this case design. I started on this project after a friend and I both broke our video transmitter antenna connector off of the board. This case adds support around the connector and antenna, allowing you to position the antenna...

This is Version 1 of this case design. I started on this project after a friend and I both broke our video transmitter antenna connector off of the board. This case adds support around the connector and antenna, allowing you to position the antenna...

A holder/box where the ImmersionRC 600mW and MinimOSD are stacked on top of eachother

Allows you to mount your ImmersionRC 5.8 UNO receiver using a gopro mount. This opens up a vast amount of mounting options including the suction cup. ... The most popular method would be to use the gopro-to-tripod adapter.

Aomway tx 5.8 Ghz 1000mw

... 1 para cámara frontal. ...Impreso en PLA Turnigy 2S 1,000mAh battery pack and ImmersionRC FPV transmitter 5.8Ghz 600mW, for DJI Inspire 1 for front camera Print in PLA Print Settings Printer: Anet A8 Rafts: Yes Supports: Yes Resolution: 0.10 Infill: 20

I designed this to hold the ImmersionRC 600mW transmitter to the side of the Phantom 2 so to maintain easy access to the battery compartment. The transmitter case is removable for servicing (and is locked in with a screw) and additional cases could...

Protection Dome / Protection Cover for 5.8 GHz Cloverleaf Antennas

A simple fpv pod for a combined camera and immersion 600mw 5.8 set, Made some adjustments and switched the stl files for the pods that now should work , even the switches on the back could be moved now and the camera mount sits a little bit tighter...

Antenna protection AOMWAY 5.8 ghz Integrated protection without cable ties ;-) No sharp corners to avoid to hook the obstacle. It's possible to use the glue to close the assembly. Do not press the antenna during assembly, use a screwdriver to push...

Shell for a 5.8 GHz 'pagoda' type antenna (by Maarten Baert). Tested with an antenna built from a Farview kit, fits nicely. ...The two halves can be glued, or just use 30mm (or larger) heat shrink to hold them together.</p> <p>This is improved over the...

I FPV at 5705Mhz, however this would work fine at 5.8 Ghz Gain is 9.39 dBi I printed in PLA Reflector is a single sided PCB I used a 40mm hole saw with the pilot bit removed. I uploaded the Sketchup file if anyone needs to modify it. as a learn more...

DIY FPV 5.8 GHz RX5808 monitor ==================== **What is it for?** This project is ment to be used by your spotter during an FPV session. Everybody enjoy the experience of FPV, but, expecially for drone pilots, is really important to have a...

100 % use 0.6 mm wire 102 % for 0.8 wire copper reflector 53 x 53 mm

Gig to make a five lobe LHCP 5.8gHz (5780hz) Rx/Tx antenna set for FPV. Use the bending tool to make the lobes and a balun (26mm). Secure the lobes with five M3x5mm screws while soldering the lobes to the RG402 cable. Then twist the balun around a...