immersionrc 600mw transmitter 3d models
4823 3d models found related to immersionrc 600mw transmitter.thingiverse
I designed this to hold the ImmersionRC 600mW transmitter to the side of the Phantom 2 so to maintain easy access to the battery compartment. The transmitter case is removable for servicing (and is locked in with a screw) and additional cases could...
thingiverse
This is a video transmitter case designed for an ImmersionRC 600mw video transmitter.
grabcad
You can open the step file as one single file, and use it to model those crazy fpv models
thingiverse
This is a vertical TX case I use for my 250 size quad-copter.
thingiverse
ImmersionRC 5.8Ghz Audio/Video Transmitter (FatShark compatible) 600mw Tx case. Protects tx while allowing cooling air flow. Supports antenna mount and prints easily with no supports. Adds flat surfaces to Velcro to. ... Check out my new design for...
cults3d
ImmersionRC 5.8Ghz Audio/Video Transmitter (FatShark compatible) 600mw Tx case. Protects tx while allowing cooling air flow. Supports antenna mount and prints easily with no supports. Adds flat surfaces to Velcro to. ... Check out my new design for...
thingiverse
I have been using the case remixed from http://www.thingiverse.com/wezze wanted to fold it to make more room.
cults3d
ImmersionRC 5.8Ghz Audio/Video Transmitter (FatShark compatible) 600mw Tx case. This split case provides much more support to the antenna mount then the one piece design. Designed for 3 zip ties, I used 1 zip tie and two bands of electrical tape so...
thingiverse
ImmersionRC 5.8Ghz Audio/Video Transmitter (FatShark compatible) 600mw Tx case. This split case provides much more support to the antenna mount then the one piece design. Designed for 3 zip ties, I used 1 zip tie and two bands of electrical tape so...
thingiverse
... 1 para cámara frontal. ...Impreso en PLA Turnigy 2S 1,000mAh battery pack and ImmersionRC FPV transmitter 5.8Ghz 600mW, for DJI Inspire 1 for front camera Print in PLA Print Settings Printer: Anet A8 Rafts: Yes Supports: Yes Resolution: 0.10 Infill: 20
thingiverse
Protection holder for the ImmersionRC 600mw vTX. Strap it down using ziptie's and the antenna plug should get a really hard time coming of in a crash. Mount the case using double sided gel tape. This is not the final version. I have a version with a...
thingiverse
A holder/box where the ImmersionRC 600mW and MinimOSD are stacked on top of eachother
thingiverse
This is a video transmitter holder built for an ImmersionRC 250mw transmitter.
thingiverse
ImmersionRC Transmitter, Lipo Battery, Lipo Watcher, 2.4 Ghz Receiver and BEC --> all in one tidyed up place. Made for Hama Star 61 Stativ. You can also place an on/off switch witch LED in the tech department to shut down everything with one switch.
thingiverse
I designed this to mount the EZUHF transmitter to the back of my Futaba 18MZ. ... It could be easily modified to fit other transmitters though. ...
thingiverse
I started on this project after a friend and I both broke our video transmitter antenna connector off of the board. This case adds support around the connector and antenna, allowing you to position the antenna or take a crash without putting stress...
youmagine
I started on this project after a friend and I both broke our video transmitter antenna connector off of the board. This case adds support around the connector and antenna, allowing you to position the antenna or take a crash without putting stress...
myminifactory
I started on this project after a friend and I both broke our video transmitter antenna connector off of the board. This case adds support around the connector and antenna, allowing you to position the antenna or take a crash without putting stress...
thingiverse
ImmersionRC 5.8Ghz Transmitter Case - linked to project : New drone from phantom 2
thingiverse
The bottom hole holds the transmitter tru the antenna plug, and the topp hole holds the antenna. ...(used spiro) It will also vent the transmitter.
cgtrader
I started on this project after a friend and I both broke our video transmitter antenna connector off of the board. This case adds support around the connector and antenna, allowing you to position the antenna or take a crash without putting stress...
thingiverse
Holder for Fat Shark 25mW transmitter which can be attached at the DJI Flamewheel F450 or the like.
thingiverse
Simple mount which holds the transmitter in a vertical orientation using the standard bolt pattern on the FlameWheel F450/F550 arm hub. ... There's a few holes for increased airflow, holes for two small cable ties, and a gusset for strength.
myminifactory
Wanted to encase the 600mw Immersion transmitter yet keeping it vented. Here the design: Custom fit Vented yet sturdy printed also in PLA 3 mm air gap on the lower side, 5 mm on the upper side. Box is designed for the transmitter module face the...
thingiverse
Wanted to encase the 600mw Immersion transmitter yet keeping it vented. Here the design: Custom fit Vented yet sturdy printed also in PLA 3 mm air gap on the lower side, 5 mm on the upper side. Box is designed for the transmitter module face...
thingiverse
This is a mount for Fat Shark (ImmersionRC) 600mW Video 5.8 Ghz transmitter for DJI Phantom for FPV (First Person View) . ... Remixed from http://www.thingiverse.com/thing:99048 This edition is smaller and has a different antenna hole
cults3d
Modified the 600mW version for the central antenna mount of 25MW vtx. ... Split the object with your slicer if you want to print on half at a time.
thingiverse
Modified the 600mW version for the central antenna mount of 25MW vtx. ... Split the object with your slicer if you want to print on half at a time.