in 1 nixie socket 3d models
2299505 3d models found related to in 1 nixie socket.thingiverse
I couldn't find any pre-made sockets for the IN-1 sized nixie tubes. These nixies are cheap on eBay because they cannot be backlit with LEDs, but they still glow nicely. Sockets for them are very hard to find for sale, so I decided to make one that...
thingiverse
IN-1 Russion nixie tubes are available on EBay is great quantity and cheap. Sockets for these tubes are nowhere to be found, so I made these. Molex 02-09-1102 connectors come in strips connected by "wings". By not completely snapping these wings...
thingiverse
Customized version of https://www.thingiverse.com/thing:3198271 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3198271
thingiverse
This is a model of the socket for IN-12, IN-15 nixie and IV-22 VFD tubes. It is constructed in OpenSCAD from the datasheet for the tubes plus measurements taken from an original bakelite socket. I omitted pins 13 & 14 because I don't have any tubes...
thingiverse
its a snug fit, I drilled the outer holes to 1.1mm to clear any blobs, slot the tube into the socket, then partially seat the pins in the back. Heat from a soldering iron seats the pins the rest of the way, and locks them in. ...The tube helps make sure...
thingiverse
Tube socket that fits over pins of IN-12b sowjet nixie tube. Do not attempt to bend the pins of IN-12 nixie tubes because the glass will shatter. The holes are close fit to the pins but the socket should slide over the pins easily. ... Before...
thingiverse
I needed a socket for my IN-2 nixie tubes. So here it is. Screw holes are for 4mm screws. The height of the socket works nicely with walls which are a couple of millimetres thick. The wooden wall in the last photo is 3mm. The metal pins have a...
thingiverse
IN-8 Nixie socket designed to fit into a standard breadboard. I used pins from a 90 degree header and pressed them into the side of the print holes. This print is very small and the tolerances are tight so I recommend using a small diameter print...
thingiverse
... part of a nixie tube socket for IN-14 nixie tubes. ...It's designed to be used with nixie tube socket pins like these: https://www.ebay.co.uk/itm/50pcs-Nixie-VFD-Tube-Socket-Female-Pin-for-IN-14-IN-16-IN-19-QS18-12-QS16-YS13-3/174283555500 (see photo).
thingiverse
I wanted a way to mount the IN-18 Nixie tube holders. I made a single block, and a block of four. I plan on using these for mounting the tubes for experimentation, and possibly building the final device. ... The single block is about 1mm...
thingiverse
Designed for IN-1 nixie tubes this clock case has room for 6 nixie tubes showing from top to bottom Hours - Minutes and Seconds. The PCB (kit) used in this build can be found in a link below. Behind the nixie clock 'tower' there is a box storing the...
prusaprinters
Having now partialy recovered (after a sucsessfull Nixie tube clock build) I thought I could save you guys some hassle and share some of my work. Here is a base for the IN-1 tubes. It is designed to take MOLEX style female connectors wich have to...
thingiverse
... build) I thought I could save you guys some hassle and share some of my work. Here is a base for the IN-1 tubes. ...It is designed to take MOLEX style female connectors wich have to opened up a slight bit with an old nail or something like it.
thingiverse
Customized version of https://www.thingiverse.com/thing:3198271 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3198271
thingiverse
Just a simple IN12 Nixie lamp socket. The pin-holes are 2mm, and you can use precision goldpin (or IC sockets) pins. When you get them off, you should drill them with 1mm bit. ...Then just put them in printed socket, and there you go.
grabcad
Socket pin model for nixie tubes like IN-12, IN-18 with 1mm pin hole
thingiverse
Requires a soldering iron to melt the tube mating pins in place.
thingiverse
... lid was held on with toothpicks. ... I ended up just heating up a small finishing nail, and pushing it in. Project Blog: Nixie Tube Fun Note: Hobby Lobby are a bunch of liars, and that does not come as a three pack. ... It's a single box.<BR> <BR>
thingiverse
... ... PCB held in place with a small self tapping screw. Link to clock seller: https://www.etsy.com/au/listing/601743969/nixie-tube-clock-assembled-kit-23-witch?ref=shop_home_active_1&pro=1 also on ebay: https://www.ebay.com.au/str/AmberNixieLight
cults3d
Nixie clock IN-14 Часы на лампах ИН-14https://www.youtube.com/watch?v=J-shGYO7y_o&feature=youtu.be
thingiverse
Nixie clock IN-14 Часы на лампах ИН-14 https://www.youtube.com/watch?v=J-shGYO7y_o&feature=youtu.be https://youtu.be/JLZmcw8IHaM
thingiverse
... a madman. ...Having now partialy recovered (after a sucsessfull Nixie tube clock build) I thought I could save you guys some hassle and share some of my work. Here is a base for the IN-12 tubes. ...It is designed to take Nixie pins as found on e-bay
prusaprinters
Having now partialy recovered (after a sucsessfull Nixie tube clock build) I thought I could save you guys some hassle and share some of my work. Here is a base for the IN-12 tubes. It is designed to take Nixie pins as found on e-bay Print...