inductrix 2 3d models

Tiny Whoop / Inductrix case designed to hold 2 Tiny Whoops, 10 USB chargers, 24 batteries and a little spot for motors, lipo checker, etc. ... Print Settings Printer: Flashforge Creator Pro ...

This also makes it to where you will not electrocute yourself trying to get the batteries off of the charger on amazon: 1S Lipo Battery Charge Board with Micro JST 1.25 and JST-PH 2.0 for Blade Inductrix Tiny Whoop mCX mCPX (XT60/USB Input) Update...

inductrix frame 2 gramm more than the orginal but stronger the motor holes must drilled, first 5,5mm than 6,0mm Print Settings Printer: colido

Frame weighs 5 grams All up weight is 21 grams, same as stock inductrix. Print Settings Printer Brand: Robo 3D Printer: ...

Alternative frame for the Blade Inductrix indoor quadcopter. I made this design after having trouble finding a design that I could reliably print on my printer(s).  My friends and I do little indoor obstacle races, and it is difficult to tell the...

Alternative frame for the Blade Inductrix indoor quadcopter. I made this design after having trouble finding a design that I could reliably print on my printer(s). My friends and I do little indoor obstacle races, and it is difficult to tell the...

... X for strengthening the four motor mounts to prevent them from brake from the frame. ...Print Settings Printer: Geeetech G2S pro (modified) Rafts: No Supports: No Resolution: 0,2 mm Infill: 100% Notes: I used PETG, 225°C, Printbed 50°C, blue tape.

2 inductrix micro drone case

monitor holder spektrum inductrix

Support for FX797T and Blade Inductrix

... and tight and the Inductrix fits in there good, and dose not rattle around at all. I hope you like it.. Print Settings Printer Brand: RepRap Printer: Pursa i3 Rafts: No Supports: No Resolution: .2 Infill: 30% Notes: Just fixed some reversed faces.

Case with lid for Inductrix FPV+. ... Holds Inductrix FPV+, 16 1S Battery Packs and USB Charger.

This is a thinner version that increases the performance of the Inductrix without sacrificing the support it gives. ...Print Settings Printer Brand: Afinia Printer: AFINIA H480 Rafts: No Supports: No Resolution: .2 Infill: medium

These brackets are for the Blade Inductrix FPV+

Case for the Inductrix FPV +, 7 lipos and charger

canopy alternative for the BLADE Inductrix Quadcopter drone.

A great stand for a Blade Inductrix Drone.

I designed this box to hold the Inductrix with an FPV camera on, it's also got space for 10 batteries. ...Enjoy but beware it's a long print. Print Settings Printer: SmartrapcoreXY Rafts: No Supports: No Resolution: 0.2 Infill: 10%

This is a container for an Inductrix FPV (not FPV +). ...It holds the Inductrix itself and has slots for 4 batteries and a charger unit.

Lunchbox tiny whoop Inductrix Print Settings Rafts: No Resolution: 0.15

Lipo case Tinywhoop - Inductrix Case for 21 Lipo (different brand) and usb charger

There are 2 version: FrameSupportV03_64: ~64mm diagonal wingspan FrameSupportV03_65: ~65mm diagonal wingspan Update Jan/05/2017: Added FrameSupportV04_65 Improved support on the inside of the motor hole and removed some material from the outside to...

... Horizon Hobby. I enlarged the case so the slightly larger Inductrix would fit and enlarged the battery holder so the larger 500mah batteries it requires fits. ...The lid fits snug but I would rather have a tight lid than have the contents fall out.

inductrix light weight frame made for simplify3d 1 to 2 walls motor cap have made out of flex Print Settings Printer: flashforge PRO Rafts: No Supports: Yes Resolution: .18 ABS Infill: 15% none used Category: R/C Vehicles

This is a quick and dirty body replacement for the Horizon Inductrix. ... It should be much more sturdy and maybe will fly better.

Yet another Inductrix Frame Support. I have used this on a busted frame with good results. ... Hopefully this will be of use to someone.

Its A three Piece Case for the Inductrix BL and Lipos the Top is 3mm thick for your own Text or Logos

Print Settings Printer Brand: FlashForge Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .2 Infill: 100% Notes: This was printed with PLA. -You need to adjust extrusion width to .3 so that it will fill the stiffener. -You may need...

I combined two items from thingivers one is the holder from https://www.thingiverse.com/thing:1815752 the second one is monitor holder spektrum inductrix https://www.thingiverse.com/thing:2119620 with a block Printed in ABS

A few different cases to hold the LIHV's for Inductrix. I haven't tested these yet but they should fit just fine. ... The angled case was designed to be wall mounted using a couple 3M Command Strips.