infinity orb 3d models
6140 3d models found related to infinity orb.thingiverse
This is an infinity orb maze cylynder, black. ... i hope you like it!
thingiverse
I made a stand that is a replica of the one from Guardians of the Galaxy for the Infinity Orb by Tonyyoungblood. You can get the link to his orb below. It does require supports and has a hollow spot for LED lighting if you desire. Enjoy! ... ...
thingiverse
This is a stand for the Guardians of the Galaxy Infinity Orb. It is a quick and easy print. I really enjoyed this model but was disappointed that it always had to be closed. ...I designed a stand that shows off the detail of the inside and gives the...
thingiverse
This is a stand for tonyyoungblood's Infinity Orb from Guardians of the Galaxy. ... Link: https://www.thingiverse.com/thing:430184
thingiverse
Ok this will be a good addition to the Guardians of the Galaxy Infinity Orb. Drilled small hold in one of the areas that the SW would fit in and fed the wires through the hole to inside the Orb. Drill another small hold in the bottom center in one of...
prusaprinters
Here's my attempt at replicating the Infinity Orb from the film Guardians of the Galaxy. In one of the pictures, you can see a side by side comparison of my orb and the orb from the film. I tried to replicate all the hole shapes to the best of my...
thingiverse
- GuardiansGalaxyInfinityOrbInteriorSideA : Partie intérieure de l'orb (A) - GuardiansGalaxyInfinityOrbInteriorSideB : Partie intérieure de l'orb (B) - GuardiansGalaxyInfinityOrbRimmagnetsv2 : partie avec les aimants permettant de joindre les deux...
thingiverse
I have uploaded two rings with recessed places for the magnets one from the front One from the back of the ring From Harbor Freight (item 67488) about $3 for 10 Rare earth Magnets 5/16” diameter x 5/64” Thick http://www.thingiverse.com/thing:430184...
thingiverse
I have taken the origional rim and cut out 3 10x5x3mm pockets. Then you can insert 3 neodynium magnets ( 10x5x2mm cheaply bought on Prime ), just remember to align the poles correctly be before gluing into place. The first one i printed with 2...
thingiverse
:) This was designed to fit the exceptional Infinity Orb that Thingiverse user tonyyoungblood (http://www.thingiverse.com/tonyyoungblood) has made available, which you can find here: http://www.thingiverse.com/thing:430184 Assembly should be pretty...
thingiverse
This is an alternate rim for tonyyoungblood's Infinity Orb - Thanks Tony! (see https://www.thingiverse.com/thing:430184). This version of the rim has recesses for installing magnets, which will hold the two halves of the orb together. Print two...
thingiverse
Here's my attempt at replicating the Infinity Orb from the film Guardians of the Galaxy. It's a work-in-progress. So far I've completed the outer shell (second draft), the rim (first draft), and both halves of the interior (final draft). . In one of...
cults3d
Here's my attempt at replicating the Infinity Orb from the film Guardians of the Galaxy. It's a work-in-progress. So far I've completed the outer shell (second draft), the rim (first draft), and both halves of the interior (final draft). . In one of...
thingiverse
I initially thought the 'base' that the orb magnetizes down onto was a solid triangle, but it instead appears to be three prongs pointing inwards. Instructions Print three (3) of the corner piece...
thingiverse
I wanted a stand for the infinity orb from Guardians of the Galaxy 1 (https://www.thingiverse.com/thing:430184) and looking at the stock image included, a simple base like this seemed to closely match what was used. Very simple design, laser cut in...
thingiverse
https://www.thingiverse.com/thing:4441076 Make amazing glowing orb of any colour or size.
prusaprinters
This is a hollow tube infinity symbol - just for fun. For an added twist (pun intended) I dropped a small (8mm) ball bearing into the print about half-way through (I should have used a slightly smaller bearing as the one I used tends to get...