innovv c3 bike camera 3d models
138144 3d models found related to innovv c3 bike camera.thingiverse
This is a simple camera mount for the Innovv C3 to fit the 2008-2012 Kawasaki Ninja 250r motorcycle. It's designed to fit on the stock rear fender. The stock fender has 3 holes, and the center hole is practically the same size as the diameter of...
thingiverse
A Lens Protector Case for the Innovv K2 camera to protect from stone chips etc. You'll need to buy & fit a 25mm Glass Watch Lens too - I used a 25mm x 2.5mm lens. I glued it in with flexible glue & I used black insulation tape to affix it to the...
thingiverse
The Innovv C5 DVR unit connects to the camera and power supply via a cable shell that has "wings" with holes for securing the cable with two screws. ... In my installation, I did not have enough clearance for these wings, so I removed them with a...
thingiverse
This is a replacement case for the INNOVV K1 main unit. Mine came with a cheesy canvas case that would cause the unit to overheat, and also allow the awful microUSB connections to come loose. This mount obviously isn't waterproof or anything...
thingiverse
Description in English and German Beschreibung in Englisch und Deutsch English Version: This Holder is made for the Innovv C5 Front Dashcam. The holder is made for the middle view angle in the front fender of the bike. I think it will fits also with...
thingiverse
GoPro Mount for bikes. ... It allows to mount a camera or a phone on the bike.
thingiverse
triumph trident 660 innovv k2 mount for front camera
thingiverse
Mount for an action camera or GoPro. ...It fits to the front of the frame of the bike on the handlebar stem.
grabcad
support and camera can be installed in front and rear of the bike and the connection will be at I-phone which will record the trip and all driver not too engaged with the bikers
thingiverse
Inspired by http://www.thingiverse.com/thing:1501 this is a camera mount to fit on the handle bars of a bike. I remade it in openSCAD as I needed a countersunk hole for the M6 bolts I had. ...
prusaprinters
A simple camera handlebar mount for bicycles. I designed this because my Apeman action cam didn't have a good mount. Since most cheap action cams use gopro compatible accessories, they should fit. This is for removable clip in adapters.</p> <h3>Print...
cults3d
Model made for the sports camera version of the mitzu brand that differs in size with the original gopro.
thingiverse
Mount to place a GoPro-type camera on the bicycle handlebar, it is designed for a standard 38.1 mm handlebar, you will need 3 M3x20 mm Allen screws, and 1 M5x45 mm hexagonal screw. The shaft is 2x10mm and is made of a TIG welding rod. Soporte...
thingiverse
Ion Air Pro Camera "Aero" mount for bike stem. Mounts using O ring or thick rubber band Angled support to allow for stem slight upward angle. Use 1/4" S.S. bolt with base hex cavity and thru hole to fasten camera to mount. ... I glued rubber inner...
grabcad
A twin rail mount for attaching a Contour Roam camera to the fork legs of your bike, if your bike has M5 rack bosses.Tested on my own gravel bike and works very well, camera is held in place securely and can be easily removed. Twin rail design...
thingiverse
I needed something to mount a Garmin Virb GPS camera to the side of my bike helmet. I don't remember exactly where I got the various adapters from the pictures (may have been with a Swann Go-Pro rip-off I bought several years ago), but the threads...
thingiverse
These are bicycle camera mounting brackets. ...They are designed to receive 1/4" - 20 thread camera mounting screws.
thingiverse
Attaching the camera to a bicycle helmet. ... This will replace the part of the cateye helmet mount(http://www.amazon.com/dp/B00ARI5YAG) 自転車のヘルメットにカメラを取り付ける為のパーツです。 Cateyeのヘルメットマウント(http://www.amazon.co.jp/dp/B00CDP8E9O) のライト取り付け部分を取り替えて使います。
thingiverse
... METALIC THREADS!!. *IMPORTANT: slid the hand strap over the handlebars before clipping on the camera (just in case.) Snap the mount on the handlebars. It should stay where it is without the tightening nut. Place screw in tightening nut. ...Enjoy!
grabcad
... is already in production-or ready to be. Please see the slides/picture for more info (the colour of the camera could easily be changed to Velodroom's own). Hope you like the elegance and simplicity... ...good luck to everyone on this challenge.
thingiverse
On long cycle rides I see loads of stuff worthy of a photo but with the camera often buried in my backpack I push on making sure to keep up a good pace. So I made this mount to clip it under the frame, so that it is hand for the chance moments and...
cults3d
This bracket allows you to attach the camera to the handlebars of your bike. ...You will need 4 M3 or M4 screws and 4 nuts or inserts.
thingiverse
Customized version of http://www.thingiverse.com/thing:82800 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=82800 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:127588 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=127588
thingiverse
Customized version of https://www.thingiverse.com/thing:247436 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=247436
thingiverse
Customized version of http://www.thingiverse.com/thing:229961 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=229961 Instructions Using the following options:...