insta 360 mount 3d models
403978 3d models found related to insta 360 mount.thingiverse
... with Insta360 mount on the top. ...Remix of StickiX by FPVFrame.ch https://www.thingiverse.com/thing:3727778 It fits these mounts from FPVWhoop: https://www.thingiverse.com/thing:4359372 Use M3 screw to put it toghether. ... Peace among worlds!
thingiverse
Insta 360 go (v1) mount for Steele 5 frame (clone Apex). ... Flight test here https://youtu.be/VlXH5yb9zTY Build log here https://youtu.be/Jqt-qtENjtg TPU...
thingiverse
This insta360 one R mount is ideally using a mount from the slammed squirt for a gopro9...
thingiverse
INSTA 360 CAMERA MOUNT FOR TBS OBLIVION http://www.team-blacksheep.com/products/prod:oblivion_pnp
cults3d
A little insta 360 go mount for the Hook from PiratFrames. ... Use this case for plug your Insta 360 go on the mount : https://www.thingiverse.com/thing:4359372
thingiverse
A little insta 360 go mount for the Hook from PiratFrames. ... Use this case for plug your Insta 360 go on the mount : https://www.thingiverse.com/thing:4359372
thingiverse
I have found few Insta 360GO camera to put in the GEPRC 3 inch quads on Thingiverse. The versions i found were supposed to be printed with flexible filaments. I few some vibrations and other things i didn't like (jellos). I believe you can use in...
thingiverse
Ein einfacher Halter für die Insta360-Remote. ...Passt genau auf den invisible-Stick.
thingiverse
A remix for using the insta 360 one on cinewhoops V1.1 for mounting via the battery strap
thingiverse
Clip & holder = 6g Clip/holder & insta 360 GO = 24g Enjoy _______________________ MOUNT (PLA) Print Settings Printer brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: BEST 0.12mm Infill: 25% Filament material: PLA...
thingiverse
remixed from the Insta360 Go2 Anti-Vibe Mount for ImpulseRC Micro Apex
thingiverse
Adding the mix files using mesh mixer in case you want to reverse the insta360 mount... ... Original was from here: https://www.thingiverse.com/thing:4766429
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
thingiverse
I wasn't unable to print this without after crash-failures, and i edited with meshmixer for a full solid design. ... Remember print i TPU Have a nice day!
cults3d
I wasn't unable to print this without after crash-failures, and i edited with meshmixer for a full solid design. ... Remember print i TPU Have a nice day!
thingiverse
Insta 360 ONE X is nice camera, but it's mount is not so nice (made from cast zinc? That fragile stuff). One faster swing with camera and it will break away from mount. I broke mine (and based on that how easily it broke away when just spinning...
thingiverse
25 degree insta360 go2 mount for Amaxinno micro series. Attaches to front screws and has hole for ziptie in the rear. ...I printed it using 95A TPU and mount turned sideways.
thingiverse
Hello, This is a mount for the GEPRC Baby Crocodile and the SMO 4k from insta360. The tilt of the camera is : 25°. You should print it horizontaly to spend less filament. ... If you want to tip, thank or help me, here is my paypal :...
thingiverse
Just some quick changes to make it fit on every quad with two straps. Print in Tpu. ... Just lay it down and print it without Support!
thingiverse
Lightweight Caddx Peanut or Insta360 GO 2 camera mount for the Armattan Gecko frame. ...Camera tilt: 25 degrees.